2.4.3 02XXXXXX
This section describes operation messages in which the upper two digits of the message identifier are 02.
Message ID |
Event Level |
Message text |
---|---|---|
Content and response |
||
02002001 |
E7 |
snmpd aborted. |
The SNMP agent program (snmpd) was forced to stop. [Action] Collect the error save information (snmpd.core file under /usr/var/core), log information, and the configuration of the SNMP agent program. Refer to the Troubleshooting Guide for information on how to collect. The SNMP agent program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch. |
||
R7 |
snmpd restarted. |
|
The SNMP agent program (snmpd) has restarted. The switch outputs this message after the SNMP agent program is forced to stop and is then restarted automatically. [Action] None. |
||
02002003 |
E7 |
rmon aborted. |
The RMON program (rmon) was forced to stop. [Action] Collect the error save information (rmon.core file under /usr/var/core), log information, and the configuration of the RMON program. Refer to the Troubleshooting Guide for information on how to collect. The RMON program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch. |
||
R7 |
rmon restarted. |
|
The RMON program (rmon) has restarted. The switch outputs this message after the RMON program is forced to stop and is then restarted automatically. [Action] None. |
||
02002010 |
E3 |
System failed switching to admin mode. |
The change to the admin mode during MIB setup has failed. [Action] Another administrator has become admin. Using the show sessions command, check the login users and admin users. |
||
02002012 |
E3 |
Specified MIB doesn't exist, or it does not have read/write attribute. |
Either the set MIB does not exist, or the MIB does not have read and write attributes. [Action] See MIB Reference to make sure that MIB you set is read/write. |
||
02002013 |
E3 |
Incorrect instance value specified. |
The instance value set during MIB setup is not correct. [Action] Check and set the instance value. |
||
02002014 |
E3 |
MIB value specified was out of range. |
You are attempting to set a MIB value that is outside the setting range during MIB setup. [Action] For details about MIB setting, see the Configuration Command Reference Vol.1" "13 SNMP. |
||
02002015 |
E3 |
Data length of the MIB value was too long. |
The entry for the MIB value set during MIB setup is too long. [Action] The number of letters that can be set as MIB can be found in Vol.1" "13 SNMP for Conformation Commands. |
||
02002016 |
E3 |
MIB Set failed due to the lack of necessary MIBs. |
MIB setup was not possible because the MIBs required for setting are insufficient. [Action] Refer to "MIB Reference" to confirm that the items required for setting are satisfied. |
||
02002017 |
E3 |
Illegal character used in MIB setting. |
You are attempting to set up the MIB using invalid characters. [Action] Check the list of character codes in the "Configuration Command Reference Vol.1" "1 : How to Read This Manual" to set. |
||
02002018 |
E3 |
MIB Set failed to configured the configuration file because the preliminary configuration file is under editing. |
Setting of a MIB into the startup configuration file was not possible because the backup configuration file is being edited. [Action] Stop editing of the backup configuration file. |
||
02002019 |
E3 |
Failed in contact the configuration file while setting up MIB. |
Access to the startup configuration file for MIB settings failed. [Action] Eliminate the cause of the access failure, and try again. |
||
02002020 |
E3 |
MIB value has failed to establish. Errors occurred in the "config" command. |
An error occurred while editing the configuration at MIB setup, and the MIB could not be set. [Action] For details on configuration errors, see Error Messages Displayed When Editing the Configuration in the manual Configuration Command Reference. |
||
02002021 |
E3 |
Not all MIB configured. |
MIB setup failed, and only some of the MIB values were set. [Action] Try setup again. If the retry still does not work, log in (for example, by using telnet) and set the MIB values. |
||
02002023 |
E3 |
System failed to save the configuration while processing MIB settings. |
While setting up MIB from an SNMP manager, an error occurred during processing to save the configuration. [Action] The configuration has not been saved. Save it (for example, by using telnet). |
||
02002024 |
E3 |
<object name> set as <mib value> at the request of <ip address> [on VRF <vrf id>]. |
<object name> was set to <mib value> because of a request from <ip address>. <object name>: MIB object mnemonic <mib value>: MIB value <ip address>: IPv4 or IPv6 address of the SNMP manager <vrf id> VRF ID [Action] None. |
||
02002025 |
E3 |
SNMP: MAC address table entry cleared at the request of <ip address> [on VRF <vrf id>]. |
The MAC address table was cleared due to a MAC address table clear request from the SNMP manager at <ip address>. <ip address>: IPv4 or IPv6 address of the SNMP manager <vrf id> VRF ID [Action] None. |