2.4.3 02XXXXXX

This section describes operation messages in which the upper two digits of the message identifier are 02.

Table 2-6: Operation messages for event location SOFTWARE (02XXXXXX)
Message ID	Event Level	Message text
Message ID	Content and response
02002001	E7	snmpd aborted.
	The SNMP agent program (snmpd) was forced to stop. [Action] Collect the error save information (snmpd.core file under /usr/var/core), log information, and the configuration of the SNMP agent program. Refer to the Troubleshooting Guide for information on how to collect. The SNMP agent program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	snmpd restarted.
	The SNMP agent program (snmpd) has restarted. The switch outputs this message after the SNMP agent program is forced to stop and is then restarted automatically. [Action] None.
02002003	E7	rmon aborted.
	The RMON program (rmon) was forced to stop. [Action] Collect the error save information (rmon.core file under /usr/var/core), log information, and the configuration of the RMON program. Refer to the Troubleshooting Guide for information on how to collect. The RMON program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	rmon restarted.
	The RMON program (rmon) has restarted. The switch outputs this message after the RMON program is forced to stop and is then restarted automatically. [Action] None.
02002010	E3	System failed switching to admin mode.
02002010	The change to the admin mode during MIB setup has failed. [Action] Another administrator has become admin. Using the show sessions command, check the login users and admin users.
02002012	E3	Specified MIB doesn't exist, or it does not have read/write attribute.
02002012	Either the set MIB does not exist, or the MIB does not have read and write attributes. [Action] See MIB Reference to make sure that MIB you set is read/write.
02002013	E3	Incorrect instance value specified.
02002013	The instance value set during MIB setup is not correct. [Action] Check and set the instance value.
02002014	E3	MIB value specified was out of range.
02002014	You are attempting to set a MIB value that is outside the setting range during MIB setup. [Action] For details about MIB setting, see "Configuration Command Reference" and "12 SNMP".
02002015	E3	Data length of the MIB value was too long.
02002015	The entry for the MIB value set during MIB setup is too long. [Action] For details about the number of characters that can be set as a MIB, see "Configuration Command Reference" and "12 SNMP".
02002016	E3	MIB Set failed due to the lack of necessary MIBs.
02002016	MIB setup was not possible because the MIBs required for setting are insufficient. [Action] Refer to "MIB Reference" to confirm that the items required for setting are satisfied.
02002017	E3	Illegal character used in MIB setting.
02002017	You are attempting to set up the MIB using invalid characters. [Action] Check the list of character codes in "1 How to Read This Manual" in the Configuration Command Reference.
02002018	E3	MIB Set failed to configured the configuration file because the preliminary configuration file is under editing.
02002018	Setting of a MIB into the startup configuration file was not possible because the backup configuration file is being edited. [Action] Stop editing of the backup configuration file.
02002019	E3	Failed in contact the configuration file while setting up MIB.
02002019	Access to the startup configuration file for MIB settings failed. [Action] Eliminate the cause of the access failure, and try again.
02002020	E3	MIB value has failed to establish. Errors occurred in the "config" command.
02002020	An error occurred while editing the configuration at MIB setup, and the MIB could not be set. [Action] For details on configuration errors, see Error Messages Displayed When Editing the Configuration in the manual Configuration Command Reference.
02002021	E3	Not all MIB configured.
02002021	MIB setup failed, and only some of the MIB values were set. [Action] Try setup again. If the retry still does not work, log in (for example, by using telnet) and set the MIB values.
02002023	E3	System failed to save the configuration while processing MIB settings.
02002023	While setting up MIB from an SNMP manager, an error occurred during processing to save the configuration. [Action] The configuration has not been saved. Save it (for example, by using telnet).
02002024	E3	<object name> set as <mib value> at the request of <ip address>.
02002024	<object name> was set to <mib value> because of a request from <ip address>. <object name>: MIB object mnemonic <mib value>: MIB value <ip address>: IPv4 or IPv6 address of the SNMP manager [Action] None.
02002025	E3	SNMP: MAC address table entry cleared at the request of <ip address>.
02002025	The MAC address table was cleared due to a MAC address table clear request from the SNMP manager at <ip address>. <ip address>: IPv4 or IPv6 address of the SNMP manager [Action] None.