redundancy force-switchover
BCU二重化構成で運用系BCUと待機系BCUを切り替えます。
[入力形式]
redundancy force-switchover [-f]
[入力モード]
一般ユーザモードおよび装置管理者モード
[パラメータ]
- -f
-
確認メッセージを出力しないでコマンドを実行します。
- 本パラメータ省略時の動作
-
確認メッセージを出力します。
[実行例]
> redundancy force-switchover Are you sure you want to switch over? (y/n): y > |
[表示説明]
なし
[通信への影響]
通信無停止機能をサポートしている機能は,系切替時でも各機能が停止しないで動作するため,系切替後も通信を維持できます。通信無停止機能を未サポートの機能は系切替後再学習をするため,ネットワーク情報が再構築されるまでの間通信が中断します。
[応答メッセージ]
メッセージ |
内容 |
---|---|
A switchover is in progress. |
現在,系切替処理中です。 |
Command execution failed because the active and standby configurations do not match. |
運用系と待機系の装置間でコンフィグレーションが不一致です。 |
Command execution failed because the configuration file was being edited. |
コンフィグレーションを編集しているため,コマンドを実行できません。 |
Command execution failed because the configuration file was being saved. |
コンフィグレーションを保存中のため,コマンドを実行できません。 |
The command cannot be executed because another user is executing 'synchronize' command. Wait a while, and then try again. |
ほかのユーザがsynchronizeコマンドを実行中です。しばらくしてから再実行してください。 |
The command cannot be executed because information is being synchronized between BCUs. Wait a while, and then try again. |
BCU二重化間で情報を同期しているため,コマンドを実行できません。しばらくしてから再実行してください。 |
The command cannot be executed because some TCP sessions are synchronizing between BCUs. Wait a while, and then try again. |
BCU二重化間でTCP高可用対象セッションの情報を同期しているため,コマンドを実行できません。しばらくしてから再実行してください。 |
The command cannot be executed because the BCU is configuring devices after a switchover. Wait a while, and then try again. |
BCUが系切替後のデバイス再設定処理中のため,コマンドを実行できません。しばらくしてから再実行してください。 |
The command cannot be executed because the system is not in a duplex state. |
二重化状態ではないため,コマンドを実行できません。 |
The command cannot be executed in the standby system. |
このコマンドは待機系では実行できません。 |
The command cannot be executed. Try again. |
コマンドを実行できません。再実行してください。 |
The command is not authorized by the RADIUS/TACACS+ server or the configuration. |
このコマンドはRADIUSサーバ,TACACS+サーバ,またはコンフィグレーションで承認されていません。 |
[注意事項]
-
本コマンドで運用系BCUと待機系BCUの系切替をした場合,再度,本コマンドを実行するときは30秒程度の間隔を空けてください。
-
本コマンド実行後から系切替が完了するまでの間に,対応するポートのコンフィグレーションが存在しないNIFを取り付けないでください。NIFを取り付ける場合は,系切替が完了してから取り付けてください。