2.11.7 2510XXXX

This section describes operation messages in which the upper four digits of the message identifier are 2510.

Table 2-24: Operation messages for event location VLAN (2510XXXX)
Message ID	Event Level	Message text
Message ID	Content and response
25100001	E4	VLAN (<vlan id>) Status is Up.
25100001	The VLAN status is UP. <vlan id>: VLAN ID [Action] None.
25100002	E4	VLAN (<vlan id>) Status is Down.
25100002	The VLAN status is DOWN. <vlan id>: VLAN ID [Action] Each line status check that belongs to VLAN.
25100005	E4	The mac-address-table static entry can't be registered at hardware tables(VLAN:<vlan id> MAC address:<mac address>).
25100005	A mac-address-table static configuration entry cannot be set in a hardware table. <vlan id>: VLAN ID <mac address>: MAC address [Action] Review the system configuration. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available. If this happens, review the parameters system l2-table mode the configuration command.
25100006	E4	The VLAN MAC Address entry can't be registered at hardware tables(VLAN:<vlan id> MAC address:<mac address>).
25100006	A VLAN MAC address entry cannot be set for hardware. <vlan id>: VLAN ID <mac address>: MAC address [Action] Review the system configuration. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
25100007	E4	Protocol based VLAN (<vlan id>) registration failed on the port(<switch no.>/<nif no.>/<port no.>).
25100007	A protocol VLAN could not be set up. You attempted to use a specification that duplicated another VLAN for which a protocol was already specified. <vlan id>: VLAN ID <switch no.>/<nif no.>/<port no.>: Switch number/NIF number/port number [Action] Review the system configuration.
25100008	E4	VLAN (<vlan id>) vlan-mac registration failed.
25100008	The vlan-mac setting failed. The number of VLANs that can be set for vlan-mac exceed the capacity limit. <vlan id>: VLAN ID [Action] Review the system configuration.
25100019	E4	The vlan mapping entry can't be registered at hardware tables(VLAN <vlan id>, port(<switch no.>/<nif no.>/<port no.>)).
25100019	Tag translation information entries cannot be registered in the hardware tables. <vlan id>: VLAN ID <switch no.>/<nif no.>/<port no.>: Switch number/NIF number/port number [Action] Review the system configuration. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
2510001b	E3	Sum of number of VLAN on ports exceeded capacity.
2510001b	The total number of VLANs for each port exceed the capacity limit. [Action] Execute any of the following measures: Use the copy command to apply the configuration file, with the total number of VLANs for each port being within the capacity limit, to the running-config file. Change the total number of VLANs to within the capacity limit, and execute the restart vlan command. Change the total number of VLANs to within the capacity limit, and restart the switch.
25100021	E4	The vlan-protocol <protocol name> registration failed on the VLAN <vlan id>.
25100021	The setting of a protocol for the protocol VLAN failed. You attempted to use a specification that duplicated a protocol already set for the port. <protocol name>: Name of the protocol that you are attempting to add <vlan id>: VLAN ID [Action] Review the system configuration.
25100022	E4	Protocol <frame type> registration failed on the vlan-protocol <protocol name>.
25100022	The setting of a protocol value used for the VLAN protocol failed. You attempted to use a specification that duplicated a protocol already set for the port. <frame type>: Frame type of the protocol that you are attempting to add ethertype <hex>: EtherType value of Ethernet V2-format frame llc <hex>: LLC value (DSAP, SSAP) of 802.3-format frame snap-ethertype <hex>: EtherType value of 802.3-format frame <protocol name>: Protocol name [Action] Review the system configuration.