2.11.3 2017XXXX [Ring Protocol]

This section describes operation messages in which the upper four digits of the message identifier are 2017.

Table 2-20: Operation messages for event location VLAN (2017XXXX)
Message ID	Event Level	Message text
Message ID	Content and response
20170001	E3	AXRP <ring id> : activated state monitoring.
20170001	Monitoring of the Ring Protocol state started. The switch outputs this message when Ring Protocol initialization is complete and you set the operation mode of the Ring Protocol configuration to the master mode. <ring id>: Ring ID [Action] None.
20170002	E3	AXRP <ring id> : detected fault recovery by receiving health check frames.
20170002	Monitoring of the Ring Protocol state detected a recovery from a failure. The switch outputs this message when it receives a health-check frame at the master node and detects a recovery from a failure. <ring id>: Ring ID [Action] None.
20170003	E3	AXRP <ring id> : cleared MAC address table by receiving flush request frames.
20170003	A flush control frame was received, and the MAC address table was cleared. <ring id>: Ring ID [Action] None.
20170004	E4	AXRP <ring id> : detected fault by health check timeout.
20170004	Monitoring of the Ring Protocol state detected a fault. The switch outputs this message when it detects a health-check timeout at the master node. <ring id>: Ring ID [Action] A fault may be occurring at the link or the node in a corresponding ring. Check the link and the node states.
20170005	E3	AXRP <ring id> : cleared MAC address table by timeout of forwarding-shift-timer.
20170005	A MAC address table was cleared due to a forwarding-shift-time timeout. The switch outputs this message when a forwarding-shift-time timeout is detected and the MAC address table is output. <ring id>: Ring ID [Action] None.
20170014	E3	AXRP(virtual-link <link id>) : cleared MAC address table by receiving flush frames.
20170014	A virtual link flush control frame was received with Ring Protocol, and MAC address table entries were cleared. This message is for the clearing of MAC address table entries for learning at all ring ports. <link id>: Virtual link ID [Action] None.
20170016	E3	AXRP <ring id> : detected fault recovery by receiving health check frames, but suspended the fault recovery process.
20170016	Monitoring of the Ring Protocol state detected a recovery from a failure, but a setting suppresses a path switchback. The switch outputs this message when it detects a recovery from a failure at the master node. <ring id>: Ring ID [Action] Either wait for the suppression-time timeout specified by the configuration command preempt-delay, or manually remove the path switchback suppression state with the command clear axrp preempt-delay.
20170017	E3	AXRP <ring id> : canceled the suspension of the fault recovery process.
20170017	Removal of Ring Protocol path switchback suppression was executed. The switch outputs this message when the path switchback suppression state is removed during such suppression at the master node. <ring id>: Ring ID [Action] None.
20170018	E3	AXRP <ring id> : activated multi fault state monitoring.
20170018	Multi-fault monitoring of Ring Protocol started. <ring id>: Ring ID [Action] None.
20170019	E3	AXRP <ring id> : detected multi fault recovery by receiving multi fault detection frames.
20170019	Multi-fault monitoring of Ring Protocol detected recovery from multiple faults. The switch outputs this message when it receives a multi-fault monitoring frame at a shared node and detects recovery from multiple faults. <ring id>: Ring ID [Action] None.
20170020	E4	AXRP <ring id> : detected multi fault by multi fault detection timeout.
20170020	Multi-fault monitoring of Ring Protocol detected multiple faults. The switch outputs this message when the multi-fault monitoring function detects a timeout at the shared node. <ring id>: Ring ID [Action] Multiple faults might be occurring in a corresponding ring. Check the link and the node states.
20170021	E3	AXRP (multi-fault-detection <ring id>) : cleared MAC address table by receiving flush frames.
20170021	A multi-fault flush control frame was received, and the MAC address table was cleared. A flush control frame for multiple failures is a flush control frame in which only MAC address table transmitted by the shared node is cleared when the multiple failure monitoring function is enabled. <ring id>: Ring ID [Action] None.
20170023	E4	AXRP <ring id> : detected fault by ring port status becoming Down.
20170023	Monitoring of the Ring Protocol state detected a fault. This message is output when the switch state is standalone and the ring port goes down on the master node. <ring id>: Ring ID [Action] Check the status of the ring port of the ring.