2.11.2 2013XXXX [GSRP]
This section describes operation messages in which the upper four digits of the message identifier are 2013.
|
Message ID |
Event Level |
Message text |
|---|---|---|
|
Content and response |
||
|
20130002 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Backup. |
|
The GSRP state transitioned to Backup. The switch outputs this message when GSRP initialization is complete, backup-lock in the GSRP configuration is deleted, or the restart vlan command is executed in the Master state while the GSRP device has not identified the partner switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130003 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Master, because the number of active ports was more than neighbor's. |
|
The GSRP state transitioned to Master because the switch has more active ports than the neighboring GSRP switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130004 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Master, because the priority was higher than neighbor's. |
|
The GSRP state transitioned to Master because the priority of the switch is higher than that of the neighboring GSRP switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130005 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Master, because the MAC address was larger than neighbor's. |
|
The GSRP state transitioned to Master because the MAC address of the switch is larger than that of the neighboring GSRP switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130006 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Master, because "set gsrp master" command was executed. |
|
The GSRP state transitioned to Master because the set gsrp master command was executed. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130007 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Master, because the direct link failure was detected. |
|
The GSRP state transitioned to Master because a direct link failure was detected. The switch outputs this message when the direct-down parameter is set in the GSRP configuration command no-neighbor-to-master, and GSRP state transitioned to Master because a direct link down was detected while in the Backup (neighbor unknown) state. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130008 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned from Master to Backup, because the number of active ports was less than neighbor's. |
|
The GSRP state transitioned from Master to Backup because the switch has fewer active ports than the neighboring GSRP switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130009 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned from Master to Backup, because the priority was lower than neighbor's. |
|
The GSRP state transitioned from Master to Backup because the priority of the switch is lower than that for the neighboring GSRP switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130010 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned from Master to Backup, because the MAC address was smaller than neighbor's. |
|
The GSRP state transitioned from Master to Backup because the MAC address of the switch is smaller than that for the neighboring GSRP switch. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130011 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Backup(No Neighbor). |
|
The GSRP state transitioned to Backup (neighbor unknown). <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] Check that the port for direct link was implemented correctly and is active. Also, check the current GSRP status by using the configuration and the operation command. |
||
|
20130012 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned from Backup(No Neighbor) to Backup. |
|
The GSRP state transitioned from Backup (neighbor unknown) to Backup. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130013 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> : advertise timeout detected on Master. |
|
The timeout period for receiving GSRP Advertise frames is detected. The switch outputs this message only when the GSRP state is Master. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] Check that the port for direct link was implemented correctly and is active. Also, check the current GSRP status by using the configuration and the operation command. |
||
|
20130014 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : advertise timeout detected on Backup(Lock). |
|
The timeout period for receiving GSRP Advertise frames is detected. The switch outputs this message only when the GSRP state is Backup (Lock). <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] Check that the port for direct link was implemented correctly and is active. Also, check the current GSRP status by using the configuration and the operation command. |
||
|
20130015 |
E3 |
GSRP aware : MAC Address Table entry cleared, because GSRP flush request received on port <port list>, GSRP <gsrp group id> VLAN group <vlan group id> Source MAC address <mac address>. |
|
The GSRP Flush Request frame was received, and the MAC address table was cleared. <port list>: Port range <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID <mac address>: MAC address [Action] None. |
||
|
20130016 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned from Master to Backup, because the double Master detected. |
|
The GSRP state of the switch and neighboring machine are both Master, so both transitioned to Backup. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] Check that the direct link port operates normally. Also, check the current GSRP status by using the configuration and the operation command. |
||
|
20130017 |
E3 |
GSRP <gsrp group id> VLAN group <vlan group id> VLAN id <vlan id> : removed from vlan-group, because configuration is a disagreement, Ring protocol and GSRP. |
|
While using the Ring Protocol there was a configuration mismatch between the Ring Protocol and GSRP, so the corresponding VLAN was no longer part of the vlan-group. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID <vlan id>: VLAN ID [Action] Change the configuration so that the contents of Ring Protocol vlan-mapping and GSRP vlan-group match. |
||
|
20130018 |
E4 |
GSRP <gsrp group id> VLAN group <vlan group id> : state transitioned to Master, because forced shift time was expired. |
|
The GSRP state transitioned to Master due to elapsing of the time set for the automatic master transition wait time. <gsrp group id>: GSRP group ID <vlan group id>: VLAN group ID [Action] None. |
||
|
20130019 |
E3 |
MAC Address Table entry cleared, because flush request received on port <port list>, Source MAC address <mac address>. |
|
The MAC address table was cleared because a Flush Request frame was received. <port list>: Port range <mac address>: Device MAC address of the frame-sending source [Action] None. |
||
|
20130020 |
E4 |
GSRP : Virtual MAC address learning frame cannot be sent in the port where capacity was exceeded. |
|
The number of VLAN ports that can send the frames for virtual MAC address learning exceeded the capacity limit. Control frames cannot be sent from VLAN ports whose capacity limit is exceeded. [Action] Decrease the number of sending ports for frames for virtual MAC address learning. Alternatively, set a longer sending interval. |
||