2.1 EQUIPMENT

This section describes the operation messages for the event location EQUIPMENT.

Table 2-1: Operation messages for event location EQUIPMENT
Message ID	Event Level	Message text
Message ID	Content and response
00000003	E3	Failed in accumulated running time access to main.
00000003	Access to the total operating time for the switch failed. [Action] This event does not affect communication and usual operation. However, you cannot use the total operating time management function. If you want to use this function, replace the device.
0000011f	E5	An access error was detected on the internal flash memory.
0000011f	An access error to the internal flash memory was detected. [Action] Replace the internal flash memory because it may be damaged.
00020102	E7	Hardware exceeded tolerance level of low temperature(<temperature> degree). Check room temperature.
	The hardware temperature went below the permissible temperature range (<temperature> degrees Celsius or lower). <temperature> -10 [Action] Check and, if necessary, improve the environment such as the room temperature around the switches. Check and, if necessary, replace the fan.
	R7	The temperature of hardware returned to normal level (<temperature> degree).
	The hardware temperature returned to normal (<temperature> degrees Celsius). <temperature> -7 [Action] None.
00020103	E7	Hardware exceeded tolerance level of high temperature (<temperature> degree). Check that room temperature and the fan is operating normally.
	The hardware temperature rose above the permissible temperature range (<temperature> degrees Celsius or higher). <temperature> 50 (with fixed power supply or FAN-04) <temperature> 40(FAN-04R is installed.) [Action] Check and improve the environment such as ventilation and heat sources around the switches. Check and, if necessary, replace the fan.
	R7	The temperature of hardware returned to normal level (<temperature> degree).
	The hardware temperature returned to normal (<temperature> degrees Celsius). <temperature> 47 (with fixed power supply or FAN-04) <temperature> 37(FAN-04R is installed.) [Action] None.
00020105	E9	Hardware is becoming high temperature which give damage to this system (<temperature> degree).
00020105	The hardware temperature has reached a temperature (<temperature> degrees Celsius or higher) that is likely to critically damage device operation. <temperature> Detected temp. over 60°C (with fixed power supply or FAN-04) <temperature> Detected temperature (50°C or more) (when FAN-04R is installed) [Action] Check and improve the environment such as ventilation and heat sources around the switches. Check and, if necessary, replace the fan.
00020106	E3	The temperature of hardware reached the warning level (<temperature> degree).
00020106	The hardware has reached the temperature that is set with the system temperature-warning-level configuration command. <temperature>: Intake air temperature of the device (in Celsius). [Action] The temperature of the device has reached the specified temperature. Check the environment surrounding the device (condition of the fan, ventilation, existence of the heat sources, etc.).
00020107	E3	The temperature of hardware came down from the warning level.
00020107	The hardware temperature has been 3 degrees Celsius or more lower than the temperature that is set with the system temperature-warning-level configuration command. [Action] None.
25000110	E8	Switching unit stopped because its hardware failure detected during the self diagnosis.
25000110	A fault was detected during hardware self-test. [Action] Replace the Switch.
25040200	R8	Hardware initialized.
25040200	The hardware has been initialized. [Action] None.
25040201	E8	Hardware restarted because of its failure.
	The switch was restarted because a hardware failure occurred at the switch. [Action] Check subsequent fault recovery log entries or fault recovery failure log entries. If the recovery was successful, operations can resume. If the recovery failed, replace the device.
	R8	Hardware recovered.
	The switch recovered from a hardware failure. [Action] None.
25040400	E8	Hardware restarted, but not recovered.
25040400	The device restarted, but it has not recovered from a hardware failure. [Action] Replace the Switch.
25040c01	E3	Corrected memory soft errors.
25040c01	The system has recovered from a memory software error. Some frames may be discarded because of the software error. [Action] None. This indicates that the memory data bits inside a switch processor might have been abruptly altered (for example by cosmic rays from a solar flare) and a software error is issued temporarily. This is not a hardware failure.
250a0210	E3	Synchronous Ethernet with internal clock was selected.
250a0210	Operation by the internal clock has started. [Action] None.