29.2.2 Checking Ring Protocol status
- <Structure of this section>
(1) Checking the configuration settings and operation status
The show axrp command can be used to check the Ring Protocol settings and operation status. Use it to check whether Ring Protocol settings set by using configuration commands have been applied properly. The show axrp <ring id list> command can be used to check the status information for each ring.
The information displayed differs depending on the contents of Oper State item. If enable is displayed for Oper State, the Ring Protocol functionality is running. The operation status of all items is indicated by the contents displayed. When - is displayed for Oper State, the item has not had its status obtained by the required configuration command. When Not Operating is displayed for Oper State, the Ring Protocol functionality cannot run because a conflict exists in the configuration. When - or Not Operating is displayed for Oper State, check the configuration.
The following figures show examples of the show axrp command and show axrp detail command.
> show axrp Date 20XX/01/27 12:00:00 UTC Total Ring Counts:4 Ring ID:1 Name:RING#1 Oper State:enable Mode:Master Attribute:- MAC Clear Mode:system VLAN Group ID Ring Port Role/State Ring Port Role/State 1 1/0/1 primary/forwarding 1/0/2 secondary/blocking 2 1/0/1 secondary/blocking 1/0/2 primary/forwarding Ring ID:2 Name:RING#2 Oper State:enable Mode:Transit Attribute:- MAC Clear Mode:system VLAN Group ID Ring Port Role/State Ring Port Role/State 1 1(ChGr) -/forwarding 2(ChGr) -/forwarding 2 1(ChGr) -/forwarding 2(ChGr) -/forwarding Ring ID:3 Name: Oper State:disable Mode:- Attribute:- MAC Clear Mode:- VLAN Group ID Ring Port Role/State Ring Port Role/State 1 - -/- - -/- 2 - -/- - -/- Ring ID:4 Name:RING#4 Oper State:enable Mode:Transit Attribute:rift-ring-edge(1) MAC Clear Mode:- Shared Edge Port:1/0/3 VLAN Group ID Ring Port Role/State Ring Port Role/State 1 1/0/3 -/- 1/0/4 -/forwarding 2 1/0/3 -/- 1/0/4 -/forwarding > |
The show axrp detail command can be used to check statistics and detailed information about the ring status for the master node. 0 is displayed for statistics unless the Ring Protocol functionality is enabled (enable is displayed for Oper State).
> show axrp detail Date 20XX/01/27 12:00:00 UTC Total Ring Counts:4 Ring ID:1 Name:RING#1 Oper State:enable Mode:Master Attribute:- MAC Clear Mode:system Control VLAN ID:5 Ring State:normal Health Check Interval (msec):1000 Health Check Hold Time (msec):3000 Flush Request Counts:3 VLAN Group ID:1 VLAN ID:6-10,12 Ring Port:1/0/1 Role:primary State:forwarding Ring Port:1/0/2 Role:secondary State:blocking VLAN Group ID:2 VLAN ID:16-20,22 Ring Port:1/0/1 Role:secondary State:blocking Ring Port:1/0/2 Role:primary State:forwarding Last Transition Time:20XX/01/24 10:00:00 Fault Counts Recovery Counts Total Flush Request Counts 1 1 12 Ring ID:2 Name:RING#2 Oper State:enable Mode : Transit Attribute : - MAC Clear Mode:system Control VLAN ID:15 Forwarding Shift Time (sec):10 Last Forwarding:flush request receive VLAN Group ID:1 VLAN ID :26-30,32 Ring Port:1(ChGr) Role:- State:forwarding Ring Port:2(ChGr) Role:- State:forwarding VLAN Group ID:2 VLAN ID:36-40,42 Ring Port:1(ChGr) Role:- State:forwarding Ring Port:2(ChGr) Role:- State:forwarding Ring ID:3 Name: Oper State:disable Mode:- Attribute:- MAC Clear Mode:- Control VLAN ID:- VLAN Group ID:1 VLAN ID:- Ring Port:- Role:- State:- Ring Port:- Role:- State:- VLAN Group ID:2 VLAN ID:- Ring Port:- Role:- State:- Ring Port:- Role:- State:- Ring ID:4 Name:RING#4 Oper State:enable Mode:Transit Attribute:rift-ring-edge(1) MAC Clear Mode:- Shared Edge Port:1/0/3 Control VLAN ID:45 Health Check Interval (msec):1000 Forwarding Shift Time (sec):10 Last Forwarding:flush request receive VLAN Group ID:1 VLAN ID:46-50,52 Ring Port:1/0/3 Role:- State:- Ring Port:1/0/4 Role:- State:forwarding VLAN Group ID:2 VLAN ID:56-60,62 Ring Port:1/0/3 Role:- State:- Ring Port:1/0/4 Role:- State:forwarding > |
When the multi-fault monitoring functionality is applied, the show axrp detail command can be used to check information about the multi-fault monitoring status.
> show axrp detail Date 20XX/03/10 12:00:00 UTC Total Ring Counts:2 Ring ID:10 Name:RING#10 Oper State:enable Mode:Master Attribute:- MAC Clear Mode:- Control VLAN ID:10 Ring State:normal Health Check Interval (msec):1000 Health Check Hold Time (msec):3000 Flush Request Counts:3 VLAN Group ID:1 VLAN ID:100-150 Ring Port:1/0/1 Role:primary State:forwarding Ring Port:1/0/2 Role:secondary State:blocking VLAN Group ID:2 VLAN ID:151-200 Ring Port:1/0/1 Role:primary State:forwarding Ring Port:1/0/2 Role:secondary State:blocking Last Transition Time:20XX/03/01 10:00:00 Fault Counts Recovery Counts Total Flush Request Counts 1 1 12 Multi Fault Detection State:normal Mode:monitoring Backup Ring ID:20 Control VLAN ID:500 Multi Fault Detection Interval (msec):2000 Multi Fault Detection Hold Time (msec):6000 Ring ID:20 Name:RING#20 Oper State:enable Mode:Transit Attribute:rift-ring-edge(1) MAC Clear Mode:- Shared Edge Port:1/0/1 Control VLAN ID:20 Health Check Interval (msec):1000 Forwarding Shift Time (sec):10 Last Forwarding:flush request receive VLAN Group ID:1 VLAN ID:100-150 Ring Port:1/0/1 Role:- State:- Ring Port:1/0/3 Role:- State:forwarding VLAN Group ID:2 VLAN ID:151-200 Ring Port:1/0/1 Role:- State:- Ring Port:1/0/3 Role:- State:forwarding > |