14.1.3 Checking the status of the switch status
You can use the operation-command show system to check the operating status of the switch and the amount of mounted memories. An example is shown below:
> show system
Date 20XX/01/16 17:53:12 UTC
System: AX3660S-48XT4QW, OS-L3M (SL-L3A-001) Ver. 12.1.D
Node : Name=
Contact=
Locate=
Elapsed time : 00:45:03
LED Brightness mode : normal
Machine ID : 0012.e23e.b20f
Power redundancy-mode : check is not executed
Power slot 1 : active PS-M(AC)
Fan : active No = Fan1(1) Speed = --------, Direction = F-to-R
PS : active
Power slot 2 : notconnect
Fan slot : active FAN-M
Fan : active No = Fan3(1) , Fan3(2) , Fan3(3) , Fan3(4)
Speed = normal , Direction = F-to-R
Lamp : ALM LED=light off
Main board : active
Boot : 20XX/01/16 17:08:19 , operation reboot
Fatal restart : CPU 0 times , SW 0 times
Lamp : Power LED=green , Status LED1=green
Board : CPU=AMD GX-420 2000MHz , Memory=4,194,304KB(4096MB)
Management port: active up
100BASE-TX full(auto) 0012.e23e.b20f
Temperature : normal(26degree)
Flash :
user area config area dump area area total
used 238,599KB 99KB 0KB 238,698KB
free 229,857KB 116,963KB 131,008KB 477,828KB
total 468,456KB 117,062KB 131,008KB 716,526KB
MC : enabled
Manufacture ID : 00000030
24,077KB used
971,008KB free
995,085KB total
System interface hundredgigabitethernet :
disable (10G) : 0/21-22,37-44
enable (100G) : 0/49,51-52
Device resources
Current selected swrt_table_resource : l3switch-2
Current selected swrt_multicast_table : Off
Current selected unicast multipath number: 4
Current selected port-channel load-balance-all-port: Off
IP routing entry :
Unicast : current number=98 , max number=8093
Multicast : current number=0 , max number=2048
ARP : current number=2 , max number=15360
IPv6 routing entry :
Unicast : current number=34 , max number=3007
Multicast : current number=0 , max number=1024
NDP : current number=2 , max number=15360
Multipath table entry : current number=0 , max number=512
MAC-Address table entry : current number=1014 , max number=81920
VXLAN Layer2 Nexthop entry : current number=0 , max number=0
System Layer2 Table Mode : mode=0
Flow detection mode : layer3-mirror-5
Used resources for filter inbound(Used/Max)
MAC IPv4 IPv6
n/a 0/1024 2/1024
Used resources for QoS(Used/Max)
MAC IPv4 IPv6
n/a 0/ 512 n/a
Used resources for UPC(Used/Max)
MAC IPv4 IPv6
n/a 0/ 512 n/a
Used resources for Mirror inbound(Used/Max)
MAC IPv4 IPv6
2/ 512 3/ 512 0/ 512
Used resources for TCP/UDP port detection pattern
Resources(Used/Max): 1/32
Destination Port Used
100-200 : -/ -/mirror
Flow detection out mode : layer3-2-out
Used resources for filter outbound(Used/Max)
MAC IPv4 IPv6
0/ 256 0/ 256 0/ 256
Flow action change
cos : enable
arp discard class : enable
arp reply cos : enable
> |
You can check the status of the fan and power supply unit, the temperature, and the total operating hours using the show environment operation command. The operation mode of the fan can be set using the system fan mode configuration command. An example is shown below:
> show environment
Date 20XX/12/10 10:00:00 UTC
Power slot 1 : PS-M(AC)
Power slot 2 : PS-M(AC)
Fan slot : FAN-M
Fan environment
Power slot 1 : Fan1(1) = active
Speed = --------
Power slot 2 : Fan2(1) = active
Speed = --------
Fan slot : Fan3(1) = active
Fan3(2) = active
Fan3(3) = active
Fan3(4) = active
Speed = normal
Fan mode : 1 (silent)
Power environment
Power slot 1 : active
Power slot 2 : active
Temperature environment
Main : 30 degrees C
Warning level : normal
Accumulated running time
Main : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
Power slot 1 : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
Power slot 2 : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
Fan slot : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
> |
The temperature-logging parameter of the show environment command allows you to check the temperature log. An example is shown below:
> show environment temperature-logging Date 20XX/12/10 20:00:00 UTC Date 0:00 6:00 12:00 18:00 20XX/12/10 - - 26.0 24.0 20XX/12/09 22.2 24.9 26.0 24.0 20XX/12/08 24.0 23.5 26.0 24.0 20XX/12/07 21.0 - 26.0 24.0 20XX/12/06 25.6 - 26.0 24.0 20XX/12/05 21.8 25.1 26.0 24.0 20XX/12/04 24.3 24.2 26.0 > |