2.1 EQUIPMENT
This section describes the operation messages for the event location EQUIPMENT.
Message ID |
Event Level |
Message text |
---|---|---|
Content and response |
||
00000003 |
E3 |
Failed in accumulated running time access to main. |
Access to the total operating time for the switch failed. [Action] This event does not affect communication and usual operation. However, you cannot use the total operating time management function. If you want to use this function, replace the device. |
||
00020102 |
E7 |
Hardware exceeded tolerance level of low temperature(<temperature> degree). Check room temperature. |
The hardware temperature went below the permissible temperature range (<temperature> degrees Celsius or lower). <temperature> 5 [Action]
|
||
R7 |
The temperature of hardware returned to normal level (<temperature> degree). |
|
The hardware temperature returned to normal (<temperature> degrees Celsius). <temperature> 8 [Action] None. |
||
00020103 |
E7 |
Hardware exceeded tolerance level of high temperature (<temperature> degree). Check that room temperature and the fan is operating normally. |
The hardware temperature rose above the permissible temperature range (<temperature> degrees Celsius or higher). <temperature> 75 [Action]
|
||
R7 |
The temperature of hardware returned to normal level (<temperature> degree). |
|
The hardware temperature returned to normal (<temperature> degrees Celsius). <temperature> 72 [Action] None. |
||
00020105 |
E9 |
Hardware is becoming high temperature which give damage to this system (<temperature> degree). |
The hardware temperature has reached a temperature (<temperature> degrees Celsius or higher) that is likely to critically damage device operation. <temperature> Temperature detected (80°C or higher) [Action]
|
||
00020106 |
E3 |
The temperature of hardware reached the warning level (<temperature> degree). |
The hardware has reached the temperature that is set with the system temperature-warning-level configuration command. <temperature> Temperature inside the device (Celsius) [Action] The temperature of the device has reached the specified temperature. Check the environment surrounding the device (condition of the fan, ventilation, existence of the heat sources, etc.). |
||
00020107 |
E3 |
The temperature of hardware came down from the warning level. |
The hardware temperature has been 3 degrees Celsius or more lower than the temperature that is set with the system temperature-warning-level configuration command. [Action] None. |
||
01200190 01200212 25040202 |
E9 |
System will restart due to hardware error detected. |
The Switch is restarted due to a hardware error. [Action] Replace the Switch. |
||
01200191 |
E9 |
System will restart to correct a transient error. When the system corrects the error, there is no need to change the system. |
Restart the equipment to repair a temporary fault. [Action] Use it as it is after rebooting. Device replacement is not required. Replace the device if it occurs frequently. |
||
01200211 2600000d 3900000b |
E9 |
The temperature of the device on this system is too high. |
The temperature of the devices making up the Switch is very high. [Action] Replace the Switch. |
||
01200214 |
E7 |
Failed in hardware temperature monitoring. |
The hardware temperature could not be acquired successfully. [Action] If it is automatically restored, use it as is. If this event continues, replace the equipment. |
||
R7 |
Hardware temperature monitoring is recoverd. |
|
The hardware temperature can now be retrieved successfully. [Action] None. |
||
25040200 |
R8 |
Hardware initialized. |
The hardware has been initialized. [Action] None. |
||
25040201 |
E8 |
Hardware restarted because of its failure. |
The switch was restarted because a hardware failure occurred at the switch. [Action] Check subsequent fault recovery log entries or fault recovery failure log entries. If the recovery was successful, operations can resume. If the recovery failed, replace the device. |
||
R8 |
Hardware recovered. |
|
The switch recovered from a hardware failure. [Action] None. |
||
25040400 |
E8 |
Hardware restarted, but not recovered. |
The device restarted, but it has not recovered from a hardware failure. [Action] Replace the Switch. |
||
25040c01 |
E3 |
Corrected memory soft errors. |
The system has recovered from a memory software error. Some frames may be discarded because of the software error. [Action] None. This indicates that the memory data bits inside a switch processor might have been abruptly altered (for example by cosmic rays from a solar flare) and a software error is issued temporarily. This is not a hardware failure. |