2.2 SFU
メッセージ種別SFUのシステムメッセージを次の表に示します。
メッセージ 識別子 |
イベント レベル |
メッセージテキスト |
---|---|---|
内容と対応 |
||
35050001 |
S6 |
The SFU was activated by a configuration command. |
コンフィグレーションコマンドpower enableによって,SFUを起動しました。 [対応] なし。 |
||
35050002 |
S6 |
The SFU was inactivated by a configuration command. |
コンフィグレーションコマンドno power enableによって,SFUを停止しました。 [対応] なし。 |
||
35050003 |
S5 |
The SFU has been extracted. |
SFUの抜去を検出しました。 [対応] SFUが抜去された,または正しく挿入されていないおそれがあります。SFUが正しく挿入されているか確認してください。 |
||
35050004 |
S5 |
The SFU has been inserted. |
SFUの挿入を検出しました。 [対応] なし。 |
||
35050101 |
S6 |
The SFU initialization is complete. |
SFUの初期化が完了しました。 [対応] なし。 |
||
35050102 |
S6 |
The SFU termination is complete. |
SFUの停止処理が完了しました。 [対応] なし。 |
||
35050103 |
S3 |
The SFU could not be initialized because the SFU was unknown. |
不明なSFUのため,初期化できません。 [対応]
|
||
35050104 |
S3 |
The SFU could not be initialized because the BCU status is fault. |
BCUが障害中状態のため,SFUを初期化できませんでした。 [対応] BCUを復旧させてください。 |
||
35050201 |
S1 |
The SFU will stop because of a hardware failure. |
SFUでハードウェア障害を検出しました。SFUを停止します。 [対応] SFUを交換してください。 |
||
35050202 |
S1 |
A hardware failure was detected during SFU self-diagnosis. The SFU will restart. |
SFUの自己診断中に障害を検出しました。SFUを再起動します。 [対応] 再起動後に,障害が回復したかどうかをメッセージで確認してください。成功した場合は継続して運用できます。失敗した場合はSFUを交換してください。 |
||
35050203 |
S6 |
The SFU recovered from a hardware failure detected during self-diagnosis. |
SFUの自己診断中に検出した障害から回復しました。 [対応] なし。 |
||
35050204 |
S1 |
The SFU will restart because of a hardware failure. |
SFUにハードウェア障害が発生したため,SFUを再起動します。 [対応] 再起動後に,障害が回復したかどうかをメッセージで確認してください。成功した場合は継続して運用できます。失敗した場合はSFUを交換してください。 |
||
35050205 |
S6 |
The SFU recovered from a hardware failure. |
SFUのハードウェア障害から回復しました。 [対応] なし。 |
||
35050206 |
S1 |
The SFU restarted, but has not recovered from a hardware failure. |
SFUを再起動しましたが,ハードウェア障害または自己診断中に検出した障害から回復しません。 [対応] SFUを交換してください。 |
||
35050207 |
S5 |
The SFU was inactivated by the 'failure-action sfu stop' configuration command. |
コンフィグレーションコマンドfailure-action sfu stopによってSFUを停止しました。 [対応] なし。 |
||
35050214 |
S1 |
The SFU will restart to correct a transient error. When the SFU corrects the error, there is no need to change the SFU. |
一時的な故障を修復するため,SFUを再起動します。 一時的な故障が正常に修復できた場合,SFUの交換は不要です。 [対応] 再起動後に,障害の回復に成功したかどうかをメッセージで確認してください。成功した場合(回復メッセージが出力された場合)は継続して運用できるため,SFUの交換は不要です。失敗した場合(回復中に障害が発生した場合)は,SFUを交換してください。 |
||
35050215 |
S6 |
The SFU corrected a transient error. |
SFUの一時的な故障から回復しました。 [対応] 継続して運用できますが,繰り返し発生する場合はSFUが故障しているおそれがあるため,交換してください。 |
||
35050301 |
S6 |
The HDC on the SFU will be updated. Do not remove the SFU. |
HDCを更新します。 [対応] 次のどちらかのメッセージが表示されるまで,SFUを抜去しないでください。
|
||
35050302 |
S6 |
The SFU will restart because its HDC was updated. |
HDCを更新したため,SFUを再起動します。 [対応] なし。 |
||
35050303 |
S3 |
The HDC update was unsuccessful on the SFU. |
HDCの更新に失敗しました。 [対応]
|
||
35050304 |
S5 |
The HDC on the SFU was updated, and to be applied after restarting the SFU. |
HDCを更新しましたが,運用に適用されていません。 [対応] SFUを再起動してください。 |
||
35050501 |
S3 |
Access to the SFU statistics failed. |
SFUの通算稼働時間へのアクセスに失敗しました。 [対応] 通信および通常運用に影響はありません。ただし,通算稼働時間の管理機能が使用できないため,使用する場合はSFUを交換してください。 |
||
35050502 |
S6 |
Access to the SFU statistics finished successfully. |
SFUの通算稼働時間へのアクセスが正常に完了しました。 [対応] なし。 |
||
350e0501 |
S6 |
The SFU online dump command was executed. |
SFUダンプ(SFU再起動なし)コマンドの実行によって,メモリダンプの収集が完了しました。 [対応] なし。 |
||
350e0502 |
S6 |
The SFU offline dump command was executed. |
SFUダンプ(SFU再起動あり)コマンドの実行によって,メモリダンプの収集が完了しました。 [対応] なし。 |
||
350e0503 |
S6 |
Collection of the SFU dump was canceled. |
ダンプ採取が中断されました。 [対応] なし。 |
||
35400501 |
S6 |
The SFU was inactivated by an operation command. |
inactivateコマンドによって,SFUを停止しました。 [対応] なし。 |
||
35400502 |
S6 |
The SFU was activated by an operation command. |
activateコマンドによって,SFUを起動しました。 [対応] なし。 |
||
35400503 |
S6 |
The SFU restarted by an operation command. |
reloadコマンドによって,SFUを再起動しました。 [対応] なし。 |