運用コマンドレファレンス Vol.1

[目次][索引][前へ][次へ]


no cp congestion-control

[機能]

回線の輻輳制御状態を運用状態に戻します。

[入力モード]

一般ユーザモードおよび装置管理者モード

[入力形式]

no cp congestion-control {nif <NIF No.> line <Line No.> | all}

[パラメータ]

nif <NIF No.>
運用状態に戻すNIF 番号を指定します。指定できるNIF番号の値の範囲は,「パラメータに指定できる値」を参照してください。

line <Line No.>
運用状態に戻すLine番号を指定します。指定できるLine番号の値の範囲は,「パラメータに指定できる値」を参照してください。

all
すべての回線について,輻輳制御状態を運用状態に戻します。

[実行例]

  1. show cp congestion-controlを実行します。
    > show cp congestion-control
    2005/03/18 13:00:10
    congestion control service status:enable
    congestion control service control-time:30 seconds
    congestion control service start time:03/01 11:50:32
    congestion control entries:1
    congestion control exception-port: -
    congestion control exception-port congestion entries:0
     
    ****** congestion control history(Most new Max 25entries) ******
    NIF1/Line0   start time: 03/18 12:56:10 end time: now controlling
     
    ****** congestion control history(Most old Max 10entries) ******
    NIF1/Line0   start time: 03/18 12:56:10 end time: now controlling
     
    ****** exception-port congestion history(Most new Max 25entries) ******
     
    ****** exception-port congestion history(Most old Max 10entries) ******
     
  2. 輻輳制御中のNIF1/Line0に対してno cp congestion-controlを実行します。
    > no cp congestion-control nif 1 line 0
    >
     
  3. show cp congestion-controlを実行し,NIF1/Line0の輻輳制御が解除されていることを確認します。
    > show cp congestion-control
    2005/03/18 13:00:20
    congestion control service status:enable
    congestion control service control-time:30 seconds
    congestion control service start time:03/01 11:50:32
    congestion control entries:1
     
    ****** congestion control history(Most new Max 25entries) ******
    NIF1/Line0   start time: 03/18 12:56:10 end time: 03/18 13:00:15
     
    ****** congestion control history(Most old Max 10entries) ******
    NIF1/Line0   start time: 03/18 12:56:10 end time: 03/18 13:00:15
     
    ****** exception-port congestion history(Most new Max 25entries) ******
     
    ****** exception-port congestion history(Most old Max 10entries) ******
     

[ユーザ通信への影響]

あり

[応答メッセージ]

表14-17 no cp congestion-controlコマンドの応答メッセージ一覧

メッセージ 内容
Can't execute this command in standby BCU. このコマンドは待機系BCU上では実行できません。
Not operational CP. CPは非運用状態です。
No congestion-control NIF <NIF No.> Line <Line No>. 指定NIF/Lineは輻輳制御中ではありません。
<NIF No.>:NIF番号
<Line No>:Line番号
Can't execute. コマンドを実行できません。

[注意事項]

なし

[目次][前へ][次へ]


[他社商品名称に関する表示]

Copyright (c) 2005, 2011, ALAXALA Networks Corporation. All rights reserved.