コンフィグレーションコマンドレファレンス Vol.1
輻輳制御に関する項目を設定します。
[入力モード]
グローバルコンフィグモード
[入力形式]
- 情報の設定
- CP輻輳制御機能の設定
- congestion-control cp
- CP輻輳制御時間の設定
- congestion-control cp [control-time <Seconds>]
- CP輻輳制御閉塞対象外ポートの設定
- congestion-control cp [exception-port <Port list>]
- 情報の変更
- CP輻輳制御時間の変更
- congestion-control cp [control-time <Seconds>]
- CP輻輳制御閉塞対象外ポートの変更
- congestion-control cp [exception-port <Port list>]
- 情報の表示
- show congestion-control
- 情報の削除
- CP輻輳制御機能の削除
- delete congestion-control
- CP輻輳制御時間の削除
- delete congestion-control cp control-time
- CP輻輳制御閉塞対象外ポートの削除
- delete congestion-control cp exception-port [<Port list>]
[サブコマンド入力形式]
なし
[モード階層]
なし
[パラメータ]
- cp
- CP輻輳が発生した場合の輻輳制御機能を有効にします。
- control-time <Seconds>
- CP輻輳制御機能の制御時間(輻輳による閉塞を行ってから閉塞解除を行うまでの時間)を指定します。
- 本パラメータ省略時の初期値
30(秒)
- 値の設定範囲
0,または10〜86400(秒)
0指定時は,一度輻輳による閉塞が行われると閉塞解除するイベント※が発生するまで輻輳による閉塞状態を解除しません。
注※ 閉塞解除するイベント
・運用コマンドno cp congestion-controlで,輻輳による閉塞状態を解除
・回線状態が運用中(正常動作中)から他の状態に変化した場合
・本パラメータの設定・変更・削除
・系切替
- exception-port <Port list>
- CP輻輳制御を行わない物理ポート番号をリスト形式で指定します。
- 【"−"または","による範囲指定】
- 範囲指定のすべてのポートを指定したことと同じ意味になります。
- 【"*"による範囲指定】
- 指定できません。
- 本パラメータ省略時の初期値
全物理ポートでCP輻輳制御を行います。
- 値の設定範囲
装置に実装されているNIF番号/Line番号
[サブコマンド]
なし
[入力例]
- 輻輳制御情報の設定
CPの輻輳制御機能を有効にします。
CPの輻輳制御時間を設定します。
(config)# congestion-control cp (config)# show congestion-control congestion-control cp (config)#
CPの輻輳制御閉塞対象外ポートを設定します。
(config)# congestion-control cp control-time 60 (config)# show congestion-control congestion-control cp control-time 60 (config)#
(config)# congestion-control cp exception-port 3/0 (config)# show congestion-control congestion-control cp exception-port 3/0 (config)#- 輻輳制御情報の表示
輻輳制御情報を表示します。
(config)# show congestion-control congestion-control cp control-time 60 congestion-control cp exception-port 0/0-2 congestion-control cp exception-port 1/0-3,5 congestion-control cp exception-port 3/0 (config)#- 輻輳制御情報の削除
CPの輻輳制御時間を削除します。
CPの輻輳制御閉塞対象外ポートNIF3/Line0を削除します。
(config)# show congestion-control congestion-control cp control-time 60 (config)# delete congestion-control cp control-time (config)# show congestion-control congestion-control cp (config)#
CPの輻輳制御閉塞対象外ポートすべてを削除します。
(config)# show congestion-control congestion-control cp exception-port 3/0 (config)# delete congestion-control cp exception-port 3/0 (config)# show congestion-control congestion-control cp (config)#
CPの輻輳制御機能を無効にします。
(config)# show congestion-control congestion-control cp exception-port 0/0-2 congestion-control cp exception-port 1/0-3,5 congestion-control cp exception-port 3/0 (config)# delete congestion-control cp exception-port (config)# show congestion-control congestion-control cp (config)#
(config)# show congestion-control congestion-control cp (config)# delete congestion-control (config)# show congestion-control (config)#
[関連コマンド]
なし
[注意事項]
- control-timeパラメータの設定・変更・削除を行った場合,設定値を反映するために本機能によって閉塞しているすべてのポートの閉塞状態を解除します。すべてのポートの閉塞解除には,16ポート輻輳制御中の場合,最大8秒掛かることがあり,すべてのポートの閉塞解除が完了するまでの間,すべてのコンフィグレーションに関して設定・変更・削除ができなくなります。
- CP輻輳制御機能で閉塞しているポートに対してexception-portパラメータの設定を行った場合,そのポートの閉塞状態を解除します。複数のポートに対してexception-portパラメータの設定を行った場合は最大8秒掛かります。
- 実装していないNIFボード配下の物理ポート番号に対してexception-portパラメータの設定を行いたい場合は,exception-portパラメータの設定を行う前にdisableコンフィグレーションの設定を行ってください。
Copyright (c)2005, 2011, ALAXALA Networks Corporation. All rights reserved.