コンフィグレーションコマンドレファレンス Vol.2

[目次][索引][前へ][次へ]


30.1.13 GSRP情報

表30-12 GSRPのエラーメッセージ

メッセージ 内容
can not configure gsrp when spanning-tree is configured. スパニングツリーの設定があるため,GSRPが設定できません。
can not configure gsrp when virtual-router is configured. VRRPの設定があるため,GSRPが設定できません。
gsrp-<gsrp group id>: can not configure layer3-redundancy when GSRP ID is not in range from 1 to 4. GSRPグループIDが1から4以外の場合,layer3-redundancyは設定できません。
GSRPグループIDを1から4の範囲で設定してください。
<gsrp group id>:GSRPグループID
gsrp-<gsrp group id>: can not specify both any flush methods and direct-link on the channel-group <channel group number>. ダイレクトリンクに設定したチャネルグループにreset-flush-portまたはno-flush-portを指定できません。
該当の設定からチャネルグループを削除するか別のチャネルグループを使用してください。
<gsrp group id>:GSRPグループID
<channel group number>:チャネルグループ番号
gsrp-<gsrp group id>: can not specify both any flush methods and direct-link on the port <nif no.>/<port no.>. ダイレクトリンクに設定したポートにreset-flush-portまたはno-flush-portを指定できません。
該当の設定からポートを削除するか別のポートを使用してください。
<gsrp group id>:GSRPグループID
<nif no.>/<port no.>:NIF番号/ポート番号
gsrp-<gsrp group id>:can not specify the two or more flush methods on the channel-group <channel group number>. 同一チャネルグループに二つ以上のフラッシュ方法は指定できません。
該当の設定からチャネルグループを削除するか別のチャネルグループを使用してください。
<gsrp group id>:GSRPグループID
<channel group number>:チャネルグループ番号
gsrp-<gsrp group id>:can not specify the two or more flush methods on the port <nif no.>/<port no.>. 同一ポートに二つ以上のフラッシュ方法は指定できません。
該当の設定からポートを削除するか別のポートを使用してください。
<gsrp group id>:GSRPグループID
<nif no.>/<port no.>:NIF番号/ポート番号
gsrp-<gsrp group id>-<vlan group id> is already configured in vlan-mapping. 指定されたVLANグループIDは,すでにVLANマッピングIDに設定されています。
Ring Protocolから該当VLANマッピングIDを削除するか,別のVLANグループIDを使用してください。
<gsrp group id>:GSRPグループID
<vlan group id>:VLANグループID
gsrp-<gsrp group id>-<vlan group id>: vlan <vlan id> has been configured in another vlan-group. 指定されたVLANはすでにほかのVLANグループに設定されています。
ほかのVLANグループから削除するか,別のVLANを使用してください。
<gsrp group id>:GSRPグループID
<vlan group id>:VLANグループID
<vlan id>:VLAN ID
Inconsistency is found between the vrf mode and the gsrp configuration. VRF機能の運用に伴い,次のどちらかの理由でコマンドを設定できません。
  • vrf modeがgsrp-enable-ipv4-ipv6以外の状態で,GSRPの設定はできません。
  • GSRPのコンフィグレーションが設定されている状態で,vrf modeをgsrp-enable-ipv4-ipv6以外に設定できません。

[目次][前へ][次へ]


[他社商品名称に関する表示]

All Rights Reserved, Copyright(C), 2006, 2018, ALAXALA Networks, Corp.