コンフィグレーションガイド Vol.1

14.1.3　装置の状態確認

運用コマンドshow systemで装置の動作状態や実装メモリ量などを確認できます。次の図に例を示します。

図14-2　装置の状態確認

> show system
Date 20XX/12/10 15:26:54 UTC
System: AX3650S-20S6XW, OS-L3SA Ver. 11.12
Node : Name=System Name
    Contact=Contact Address
    Locate=Location
    Elapsed time : 04:32:13
    LED Brightness mode : normal
    Machine ID : 0012.e222.1dd3
    Power redundancy-mode : check is not executed
    Power slot 1 : active PS-M(AC)
        Fan  : active No = Fan1(1) Speed = normal
        PS   : active
        Lamp : Power LED=green , ALM1 LED=light off , ALM2 LED=light off
    Power slot 2 : active PS-M(AC)
        Fan  : active No = Fan2(1) Speed = normal
        PS   : active
        Lamp : Power LED=green , ALM1 LED=light off , ALM2 LED=light off
    Fan slot : active FAN-M
        Fan  : active No = Fan3(1) , Fan3(2) , Fan3(3) , Fan3(4) Speed = normal
        Lamp : ALM LED=light off
    Main board : active
        Boot : 20XX/12/10 10:54:49 , operation reboot
        Fatal restart : CPU 0 times ,  SW 0 times
        Lamp : Power LED=green , Status LED1=green
        Board : CPU=PowerPC 800MHz , Memory=1,048,576kB(1024MB)
        Temperature : normal(28degree)
        Flash :
                  user area   config area     dump area    area total
            used  121,161kB         289kB           0kB     121,450kB
            free   14,619kB      75,117kB      65,390kB     155,126kB
            total 135,780kB      75,406kB      65,390kB     276,576kB
        MC  : notconnect
    Device resources
        Current selected swrt_table_resource: l3switch-2
        Current selected swrt_multicast_table: On
        Current selected unicast multipath number: 8
        IP routing entry :
            Unicast : current number=6 , max number=8192
            Multicast : current number=0 , max number=1024
            ARP : current number=1 , max number=2048
        IPv6 routing entry :
            Unicast : current number=1 , max number=4096
            Multicast : current number=0 , max number=256
            NDP : current number=0 , max number=2048
        Multipath table entry : current number=3 , max number=256
        MAC-Address table entry : current number=7 , max number=32768
        System Layer2 Table Mode : auto (mode=1)
        Flow detection mode : layer3-1
          Used resources for filter inbound(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1-24       :   0/512   30/512      n/a
            Port 0/25-48       :   0/512   24/512      n/a
            Port 0/49-52       :   0/512   24/512      n/a
            VLAN               :   0/512    2/512      n/a
          Used resources for QoS inbound(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1-52       :   0/256   26/256      n/a
            VLAN               :   0/256    2/256      n/a
          Used resources for UPC inbound(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1-52       :   0/256   26/256      n/a
            VLAN               :   0/256    2/256      n/a
          Used resources for TCP/UDP port detection pattern
            Resources(Used/Max):  3/32
        Flow detection out mode : layer3-3-out
          Used resources for filter outbound(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1-52       :     n/a      n/a      n/a
            VLAN               : 256/256  256/256  256/256
        Flow action change
            cos                : enable
>

運用コマンドshow environmentでファン，電源，温度の状態，累積稼働時間を確認できます。ファンの運転モードはコンフィグレーションコマンドsystem fan modeで設定できます。次の図に例を示します。

図14-3　装置の環境状態確認

> show environment
Date 20XX/12/10 10:00:00 UTC
Power slot 1 : PS-M(AC)
Power slot 2 : PS-M(AC)
Fan slot     : FAN-M
 
Fan environment
    Power slot 1 : Fan1(1) = active
                   Speed = normal
    Power slot 2 : Fan2(1) = active
                   Speed = normal
    Fan slot     : Fan3(1) = active
                   Fan3(2) = active
                   Fan3(3) = active
                   Fan3(4) = active
                   Speed = normal
    Fan mode     : 1 (silent)
 
Power environment
    Power slot 1 : active
    Power slot 2 : active
 
Temperature environment
    Main  :  30 degrees C
    Warning level : normal
 
Accumulated running time
    Main         :  total    : 365 days and 18 hours.
                    critical : 10 days and 8 hours.
    Power slot 1 :  total    : 365 days and 18 hours.
                    critical : 10 days and 8 hours.
    Power slot 2 :  total    : 365 days and 18 hours.
                    critical : 10 days and 8 hours.
    Fan slot     :  total    : 365 days and 18 hours.
                    critical : 10 days and 8 hours.
>

運用コマンドshow environmentのtemperature-loggingパラメータで温度履歴情報を確認できます。次の図に例を示します。

図14-4　温度履歴情報の確認

> show environment temperature-logging
Date 20XX/12/10 20:00:00 UTC
Date         0:00  6:00 12:00 18:00
20XX/12/10      -     -  26.0  24.0
20XX/12/09   22.2  24.9  26.0  24.0
20XX/12/08   24.0  23.5  26.0  24.0
20XX/12/07   21.0     -  26.0  24.0
20XX/12/06   25.6     -  26.0  24.0
20XX/12/05   21.8  25.1  26.0  24.0
20XX/12/04   24.3  24.2  26.0
>

[目次][前へ][次へ]

[商品名称に関する表示]

14.1.3 装置の状態確認

14.1.3　装置の状態確認