14.1.3 装置の状態確認
運用コマンドshow systemで装置の動作状態や実装メモリ量などを確認できます。次の図に例を示します。
> show system
Date 20XX/01/16 17:53:12 UTC
System: AX3660S-48XT4QW, OS-L3M (SL-L3A-001) Ver. 12.1.D
Node : Name=
Contact=
Locate=
Elapsed time : 00:45:03
LED Brightness mode : normal
Machine ID : 0012.e23e.b20f
Power redundancy-mode : check is not executed
Power slot 1 : active PS-M(AC)
Fan : active No = Fan1(1) Speed = --------, Direction = F-to-R
PS : active
Power slot 2 : notconnect
Fan slot : active FAN-M
Fan : active No = Fan3(1) , Fan3(2) , Fan3(3) , Fan3(4)
Speed = normal , Direction = F-to-R
Lamp : ALM LED=light off
Main board : active
Boot : 20XX/01/16 17:08:19 , operation reboot
Fatal restart : CPU 0 times , SW 0 times
Lamp : Power LED=green , Status LED1=green
Board : CPU=AMD GX-420 2000MHz , Memory=4,194,304KB(4096MB)
Management port: active up
100BASE-TX full(auto) 0012.e23e.b20f
Temperature : normal(26degree)
Flash :
user area config area dump area area total
used 238,599KB 99KB 0KB 238,698KB
free 229,857KB 116,963KB 131,008KB 477,828KB
total 468,456KB 117,062KB 131,008KB 716,526KB
MC : enabled
Manufacture ID : 00000030
24,077KB used
971,008KB free
995,085KB total
System interface hundredgigabitethernet :
disable (10G) : 0/21-22,37-44
enable (100G) : 0/49,51-52
Device resources
Current selected swrt_table_resource : l3switch-2
Current selected swrt_multicast_table : Off
Current selected unicast multipath number: 4
Current selected port-channel load-balance-all-port: Off
IP routing entry :
Unicast : current number=98 , max number=8093
Multicast : current number=0 , max number=2048
ARP : current number=2 , max number=15360
IPv6 routing entry :
Unicast : current number=34 , max number=3007
Multicast : current number=0 , max number=1024
NDP : current number=2 , max number=15360
Multipath table entry : current number=0 , max number=512
MAC-Address table entry : current number=1014 , max number=81920
VXLAN Layer2 Nexthop entry : current number=0 , max number=0
System Layer2 Table Mode : mode=0
Flow detection mode : layer3-mirror-5
Used resources for filter inbound(Used/Max)
MAC IPv4 IPv6
n/a 0/1024 2/1024
Used resources for QoS(Used/Max)
MAC IPv4 IPv6
n/a 0/ 512 n/a
Used resources for UPC(Used/Max)
MAC IPv4 IPv6
n/a 0/ 512 n/a
Used resources for Mirror inbound(Used/Max)
MAC IPv4 IPv6
2/ 512 3/ 512 0/ 512
Used resources for TCP/UDP port detection pattern
Resources(Used/Max): 1/32
Destination Port Used
100-200 : -/ -/mirror
Flow detection out mode : layer3-2-out
Used resources for filter outbound(Used/Max)
MAC IPv4 IPv6
0/ 256 0/ 256 0/ 256
Flow action change
cos : enable
arp discard class : enable
arp reply cos : enable
> |
運用コマンドshow environmentでファン，電源，温度の状態，累積稼働時間を確認できます。ファンの運転モードはコンフィグレーションコマンドsystem fan modeで設定できます。次の図に例を示します。
> show environment
Date 20XX/12/10 10:00:00 UTC
Power slot 1 : PS-M(AC)
Power slot 2 : PS-M(AC)
Fan slot : FAN-M
Fan environment
Power slot 1 : Fan1(1) = active
Speed = --------
Power slot 2 : Fan2(1) = active
Speed = --------
Fan slot : Fan3(1) = active
Fan3(2) = active
Fan3(3) = active
Fan3(4) = active
Speed = normal
Fan mode : 1 (silent)
Power environment
Power slot 1 : active
Power slot 2 : active
Temperature environment
Main : 30 degrees C
Warning level : normal
Accumulated running time
Main : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
Power slot 1 : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
Power slot 2 : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
Fan slot : total : 365 days and 18 hours.
critical : 10 days and 8 hours.
> |
運用コマンドshow environmentのtemperature-loggingパラメータで温度履歴情報を確認できます。次の図に例を示します。
> show environment temperature-logging Date 20XX/12/10 20:00:00 UTC Date 0:00 6:00 12:00 18:00 20XX/12/10 - - 26.0 24.0 20XX/12/09 22.2 24.9 26.0 24.0 20XX/12/08 24.0 23.5 26.0 24.0 20XX/12/07 21.0 - 26.0 24.0 20XX/12/06 25.6 - 26.0 24.0 20XX/12/05 21.8 25.1 26.0 24.0 20XX/12/04 24.3 24.2 26.0 > |