コンフィグレーションコマンドレファレンス Vol.1
表45-11 イーサネットのエラーメッセージ
メッセージ 内容 'network-clock input-source' cannot be set, because specified port is already set by other input-source. 指定したポートはすでに使用されているため,設定できません。 'network-clock input-source' cannot be set, because specified priority is already set for the same switch number. 指定した優先度は同じ番号の装置ですでに使用されているため,設定できません。 'network-clock input-source' cannot be set, because specified switch model does not support Sync-E. 指定したスイッチのモデルはSync-Eをサポートしていないため,設定できません。 A subinterface cannot be set because a channel-group is already set for the port. 該当するポートはチャネルグループに設定されているため,サブインタフェースには設定できません。
サブインタフェースを指定する場合は,チャネルグループに設定していないポートを指定してください。A subinterface cannot be set because a switchport is already set for the Ethernet port. イーサネットポートにswitchportが設定されているため,サブインタフェースの設定ができません。
サブインタフェースを指定する場合は,no switchportが設定されているインタフェースを指定してください。A switchport cannot be set because a subinterface is already set for the Ethernet port. イーサネットポートにサブインタフェースが設定されているため,switchport mode設定ができません。
switchportを設定する場合は,サブインタフェースが設定されていないインタフェースを指定するか,サブインタフェースを削除してください。Cannot attach the interface specified as a ring-port to the channel-group. リングポートに指定したインタフェースをポートチャネルに参加させることはできません。
指定したインタフェースをポートチャネルに参加させる場合には,リングに関する設定を削除してから実施してください。Cannot attach the interface that specified cfm enable to the channel-group. CFMのenableを設定したインタフェースをポートチャネルに参加させることはできません。
設定したインタフェースをポートチャネルに参加させる場合には,CFMのenableを削除してから実施してください。Cannot attach the interface that specified mep to the channel-group. MEPを設定したインタフェースをポートチャネルに参加させることはできません。
設定したインタフェースをポートチャネルに参加させる場合には,MEPを削除してから実施してください。Cannot attach the interface that specified mip to the channel-group. MIPを設定したインタフェースをポートチャネルに参加させることはできません。
設定したインタフェースをポートチャネルに参加させる場合には,MIPを削除してから実施してください。Cannot attach the interface that specified ptp enable to the channel-group. PTPのenableを設定したインタフェースをポートチャネルに参加させることはできません。
インタフェースをポートチャネルに参加させる場合には,PTPのenableを削除してから実施してください。The number of interfaces exceeds the maximum number for this device. インタフェース数が本装置の収容最大数を超えました。
装置内の設定内容を確認して,使用していないサブインタフェースを削除してください。this command is different from this one in channel-group port. ポートチャネルの設定内容と不一致です。
ポートチャネルの設定内容を一致させてください。
All Rights Reserved, Copyright(C), 2017, 2020, ALAXALA Networks, Corp.