12.1.3 装置の状態確認
運用コマンドshow systemで装置の動作状態や実装メモリ量などを確認できます。次の図に例を示します。
> show system
Date 20XX/12/15 06:35:27 UTC
System: AX3640S-24TW, OS-L3A Ver. 11.12
Node : Name=System Name
Contact=Contact Address
Locate=Location
Elapsed time : 2days 03:25:01
Machine ID : 0012.e268.2c21
Power redundancy-mode : check is not executed
Module slot 1 : active PS-M(AC)
Fan : active No = Fan1(1) , Fan1(2) Speed = normal
PS : active
Lamp : Power LED=green , ALM1 LED=light off , ALM2 LED=light off
Module slot 2 : active FAN-M
Fan : active No = Fan2(1) , Fan2(2) Speed = normal
PS : not power supply module
Lamp : ALM LED=light off
Main board : active
Boot : 20XX/12/13 03:10:15 , power on
Fatal restart : CPU 0 times, SW 0 times
Lamp : Power LED=green , Status LED1=green
Board : CPU=PowerPC 533MHz , Memory=524,304kB(512MB)
Temperature : normal(27degree)
Flash :
user area config area dump area area total
used 35,240kB 57kB 2,444kB 37,741kB
free 2,439kB 7,208kB 5,660kB 15,307kB
total 37,679kB 7,265kB 8,104kB 53,048kB
MC : notconnect
Device resources
Current selected swrt_table_resource: l3switch-2
Current selected swrt_multicast_table: On
Current selected unicast multipath number: 8
IP routing entry :
Unicast : current number=5 , max number=8192
Multicast : current number=5 , max number=256
ARP : current number=2 , max number=1024
IPv6 routing entry :
Unicast : current number=2 , max number=2048
Multicast : current number=5 , max number=128
NDP : current number=2 , max number=1024
Multipath table entry : current number=0 , max number=128
MAC-Address table entry(Unit1) : current number=2 , max number=32768
MAC-Address table entry(Unit2) : current number= - , max number= -
System Layer2 Table Mode : mode=0
Flow detection mode : layer3-2
Used resources for filter inbound(Used/Max)
MAC IPv4 IPv6
Port 0/ 1- 3 : n/a 30/256 n/a
Port 0/ 4- 6 : n/a 24/256 n/a
Port 0/ 7- 9 : n/a 24/256 n/a
Port 0/10-12 : n/a 24/256 n/a
Port 0/13-15 : n/a 24/256 n/a
Port 0/16-18 : n/a 24/256 n/a
Port 0/19-21 : n/a 24/256 n/a
Port 0/22-24 : n/a 2/256 n/a
VLAN : n/a n/a n/a
Used resources for QoS(Used/Max)
MAC IPv4 IPv6
Port 0/ 1- 6 : n/a 18/128 n/a
Port 0/ 7-12 : n/a 10/128 n/a
Port 0/13-18 : n/a 10/128 n/a
Port 0/19-24 : n/a 10/128 n/a
VLAN : n/a n/a n/a
Used resources for UPC(Used/Max)
MAC IPv4 IPv6
Port 0/ 1- 6 : n/a 20/128 n/a
Port 0/ 7-12 : n/a 10/128 n/a
Port 0/13-18 : n/a 10/128 n/a
Port 0/19-24 : n/a 10/128 n/a
VLAN : n/a n/a n/a
Used resources for TCP/UDP port detection pattern
Resources(Used/Max): 0/16
Flow detection out mode : layer3-1-out
Used resources for filter outbound(Used/Max)
MAC IPv4 IPv6
Port 0/ 1- 6 : n/a 30/128 n/a
Port 0/ 7-12 : n/a 24/128 n/a
Port 0/13-18 : n/a 24/128 n/a
Port 0/19-24 : n/a 24/128 n/a
VLAN : n/a n/a n/a
> |
運用コマンドshow environmentでファン，電源，温度の状態，累積稼働時間を確認できます。ファンの運転モードはコンフィグレーションコマンドsystem fan modeで設定できます。次の図に例を示します。
> show environment
Date 20XX/12/10 10:00:00 UTC
Fan environment
Fan : active
Speed : normal
Mode : 2 (cool)
Power environment
PS : active
EPU : active
Temperature environment
Main : 27 degrees C
Warning level : normal
Accumulated running time
Main : total : 365 days and 18 hours.
critical : 202 days and 22 hours.
> |
運用コマンドshow environmentのtemperature-loggingパラメータで温度履歴情報を確認できます。次の図に例を示します。
> show environment temperature-logging Date 20XX/12/10 20:00:00 UTC Date 0:00 6:00 12:00 18:00 20XX/12/10 - - 26.0 24.0 20XX/12/09 22.2 24.9 26.0 24.0 20XX/12/08 24.0 23.5 26.0 24.0 20XX/12/07 21.0 - 26.0 24.0 20XX/12/06 25.6 - 26.0 24.0 20XX/12/05 21.8 25.1 26.0 24.0 20XX/12/04 24.3 24.2 26.0 > |