コンフィグレーションガイド Vol.1

11.1.3　装置の状態確認

運用コマンドshow systemで装置の動作状態や搭載メモリ量などを確認できます。次の図に例を示します。

図11-2　装置の状態確認

> show system
Date 20XX/12/15 06:35:27 UTC
System: AX3630S-24T2X, OS-L3A Ver. 11.5
Node : Name=System Name
    Contact=Contact Address
    Locate=Location
    Elapsed time : 2days 03:25:01
    Machine ID : 0012.e268.2c21
    Power redundancy-mode : check is not executed
    Fan : active Speed=normal
    PS  : active
    EPU : notconnect
    Main board : active
        Boot : 20XX/12/13 03:10:15 , power on
        Fatal restart : CPU 0 times, SW 0 times
        Lamp : Power LED=green , Status LED1=green
        Board : CPU=PowerPC 533MHz , Memory=524,304kB(512MB)
        Temperature : normal(27degree)
        Flash :
                  user area   config area     dump area    area total
            used   35,240kB          57kB       2,444kB      37,741kB
            free    2,439kB       7,208kB       5,660kB      15,307kB
            total  37,679kB       7,265kB       8,104kB      53,048kB
        MC : notconnect
    Device resources
        Current selected swrt_table_resource: l3switch-2
        Current selected swrt_multicast_table: On
        Current selected unicast multipath number: 8
        IP routing entry :
            Unicast : current number=5 , max number=8192
            Multicast : current number=5 , max number=256
            ARP : current number=2 , max number=102
        IPv6 routing entry :
            Unicast : current number=2 , max number=2048
            Multicast : current number=5 , max number=128
            NDP : current number=2 , max number=1024
        MAC-Address table entry(Unit1) : current number=2 , max number=16384
        MAC-Address table entry(Unit2) : current number= - , max number= -
        System Layer2 Table Mode : auto (mode=1)
        Flow detection mode : layer3-1
          Used resources for filter(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1- 8,25-26 :   0/128   30/128      n/a
            Port 0/ 9-16       :   0/128   24/128      n/a
            Port 0/17-24       :   0/128   24/128      n/a
            VLAN               :   0/128    2/128      n/a
          Used resources for QoS(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1-26       :    0/64    26/64      n/a
            VLAN               :    0/64     2/64      n/a
          Used resources for UPC(Used/Max)
                                     MAC     IPv4     IPv6
            Port 0/ 1-26       :    0/64    26/64      n/a
            VLAN               :    0/64     2/64      n/a
          Used resources for TCP/UDP port detection pattern
            Resources(Used/Max):  3/16
              Source Port
                10-20          :   filter/  -
              Destination Port
                1-2            :        -/QoS
                65534-65535    :   filter/QoS
        Flow action change
            cos                : enable
>

運用コマンドshow environmentでファン，電源，温度の状態，累積稼働時間を確認できます。ファンの運転モードはコンフィグレーションコマンドsystem fan modeで設定できます。次の図に例を示します。

図11-3　装置の環境状態確認

> show environment
Date 20XX/12/10 10:00:00 UTC
Fan environment 
    Fan   : active
    Speed : normal
    Mode  : 2 (cool)
 
Power environment
    PS    : active
    EPU   : active
 
Temperature environment
    Main  :  27 degrees C
    Warning level : normal
 
Accumulated running time
    Main  :  total    : 365 days and 18 hours.
             critical : 202 days and 22 hours.
>

運用コマンドshow environmentのtemperature-loggingパラメータで温度履歴情報を確認できます。次の図に例を示します。

図11-4　温度履歴情報の確認

> show environment temperature-logging
Date 20XX/12/10 20:00:00 UTC
Date         0:00  6:00 12:00 18:00
20XX/12/10      -     -  26.0  24.0
20XX/12/09   22.2  24.9  26.0  24.0
20XX/12/08   24.0  23.5  26.0  24.0
20XX/12/07   21.0     -  26.0  24.0
20XX/12/06   25.6     -  26.0  24.0
20XX/12/05   21.8  25.1  26.0  24.0
20XX/12/04   24.3  24.2  26.0
>

[目次][前へ][次へ]

[他社商品名称に関する表示]

11.1.3 装置の状態確認

11.1.3　装置の状態確認