構成定義コマンドレファレンス Vol.2
HDLCパススルーのQoS情報を設定します。装置当たり,最大160エントリ作成できます。
[入力モード]
グローバルコンフィグモード
[入力形式]
- 情報の設定,変更
- qos-hdlc-passthrough {<Line Name> | <DLCI Name> | <VC Name> | <Group Name> | <Timeslot Name> | <Peer Name>} [ priority_class <No.> ] [ discard_class <No.> ]
- 情報の削除
- delete qos-hdlc-passthrough {<Line Name> | <DLCI Name> | <VC Name> | <Group Name> | <Timeslot Name> | <Peer Name>}
- 情報の表示
- show qos-hdlc-passthrough [{<Line Name> | <DLCI Name> | <VC Name> | <Group Name> | <Timeslot Name> | <Peer Name>}]
[サブコマンド入力形式]
なし
[モード階層]
なし
[パラメータ]
- { <Line Name> | <DLCI Name> | <VC Name> | <Group Name> | <Timeslot Name> | <Peer Name> }
- ブリッジインタフェース情報で設定した対象インタフェース名称を指定します。(本コマンド入力前にブリッジインタフェース情報を設定済みであること。)WANインタフェースだけ指定可能です。LAN,ATMインタフェースのHDLCパススルーのQoS情報はqos-bridgeで設定した値で動作します。
- 本パラメータ省略時の初期値
省略できません。
- priority_class <No.>
- 出力優先度を指定します。完全優先の場合は出力優先度として,最低帯域保証,ラウンドロビンの場合はキュー番号として使用します。ただし,インタフェース名称がATMのVC,およびATMのVCをグループ化した<Group Name>の場合は設定は無効とします。
- 本パラメータ省略時の初期値
4
- 値の設定範囲
1〜8
- discard_class <No.>
- キューイング優先度を指定します。
- 本パラメータ省略時の初期値
4
- 値の設定範囲
1〜4
[サブコマンド]
なし
[入力例]
- 情報の設定
インタフェース名称office1に出力優先度3,キューイング優先度1を設定します。
(config)# bridge-interface office1 yes [bridge-interface office1 yes] (config)# exit (config)# qos (config)# qos-hdlc-passthrough office1 priority_class 3 discard_class 1 (config)# show qos-hdlc-passthrough qos-hdlc-passthrough office1 discard_class 1 priority_class 3 (config)#- 情報の変更
インタフェース名称office1のキューイング優先度を1から2に変更します。
(config)# show qos-hdlc-passthrough qos-hdlc-passthrough office1 discard_class 1 priority_class 3 (config)# qos-hdlc-passthrough office1 discard_class 2 (config)# show qos-hdlc-passthrough qos-hdlc-passthrough office1 discard_class 2 priority_class 3 (config)#- 設定情報の表示
- すべて表示します。
(config)# show qos-hdlc-passthrough qos-hdlc-passthrough office1 discard_class 2 priority_class 3 qos-hdlc-passthrough office2 discard_class 2 priority_class 4 (config)#
- 任意のインタフェース名称を表示します。
(config)# show qos-hdlc-passthrough office1 qos-hdlc-passthrough office1 discard_class 2 priority_class 3 (config)#- 設定情報の削除
インタフェース名称office1の設定を削除します。
(config)# show qos-hdlc-passthrough qos-hdlc-passthrough office1 discard_class 2 priority_class 3 qos-hdlc-passthrough office2 discard_class 2 priority_class 4 (config)# delete qos-hdlc-passthrough office1 (config)# show qos-hdlc-passthrough qos-hdlc-passthrough office2 discard_class 2 priority_class 4 (config)#- パラメータの削除
インタフェース名称office1のdiscard_classを削除します。
(config)# show qos-hdlc-passthrough qos-hdlc-passthrough office1 discard_class 2 priority_class 3 (config)# delete qos-hdlc-passthrough office1 discard_class (config)# show qos-hdlc-passthrough qos-hdlc-passthrough office2 priority_class 4 (config)#
[関連コマンド]
qos,qos-queue-list,qos-interface,qos-discard-mode,bridge-interface
[注意事項]
IPルーティングプロトコル情報,IPマルチキャストルーティングプロトコル情報の変更を行い,applyコマンドを実行していない場合,本コマンドを入力するとコマンドの実行前にapplyコマンドを自動で実行し,変更したIPルーティングプロトコル情報,IPマルチキャストルーティングプロトコル情報が運用に反映されます。
Copyright (c)2005 ALAXALA Networks Corporation. All rights reserved.