2.4.6 11XXXXXX-1fXXXXXX

This section describes operation messages in which the two most significant digits of the message identifier are 1f from 11.

Table 2-9: Operation messages for event location SOFTWARE (11XXXXXX-)
Message ID	Event Level	Message text
Message ID	Content and response
11010001	E3	The list number <policy list no.> of the policy base routing changed to the sequence number <sequence>.
11010001	The route with priority <sequence> was selected in the list number <policy list no.> of the policy-based routing. <policy list no.>: The list number of the policy-based routing <sequence>: Priority of routing information in the list [Action] None.
11010002	E3	The list number <policy list no.> of the policy base routing changed to the default operation.
11010002	The default was selected in the list number <policy list no.> of the policy-based routing. <policy list no.>: The list number of the policy-based routing [Action] None.
11109901	E7	policyd aborted.
	The policy-based program (policyd) was forced to stop. [Action] Collect the error save information (policyd.core file under /usr/var/core), log information, and the configuration of the policy-based program. Refer to the Troubleshooting Guide for information on how to collect. The policy-based program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	policyd restarted.
	The policy-based program (policyd) has restarted. The switch outputs this message when the policy-based program restarts automatically or a restart is requested by the restart policy command. [Action] None.
1920a002	E7	mr6 aborted.
	IPv6 multicast routing program was forced to stop. [Action] Check if other logs related to IPv6 multicast routing program (message type: MR6) have occurred, and then take the corresponding action. The IPv6 multicast routing program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	mr6 restarted.
	The IPv6 multicast routing program has restarted. The switch outputs this message when the IPv6 multicast routing program restarts automatically or a restart is requested by the restart ipv6-multicast command. [Action] None.
1920a003	E3	The multicast routing program will restart, because the multicast (PIM6) max-interfaces configuration changed.
1920a003	The IPv6 multicast routing program will restart because the IPv6 multicast (PIM6) information of the running configuration was changed by the configuration command ipv6 pim max-interface. [Action] None.
1920a005	E3	IPv6 multicast routing entry had exceeded maximum value <number> for limit, entry has discarded[ on VRF <vrf id>].
1920a005	An entry was discarded because the IPv6 multicast routing information exceeds the limit maximum value of <number> <number>: Maximum number of items of IPv6 multicast routing information <vrf id> VRF ID [Action] An unauthorized access might have occurred. Check if more than the expected number of additional requests for multicast routing information were generated. The number of items of multicast routing information exceeds the limit maximum value. Check the configuration (ipv6 pim mroute-limit command). Check the network configuration and reconsider the configuration of the Switch.
1920a006	E3	IPv6 multicast routing entry has recovered from the state of discard[ on VRF <vrf id>].
1920a006	IPv6 multicast routing information has recovered from state in which entries were discarded. <vrf id> VRF ID [Action] None.
1920a007	E3	IPv6 multicast forwarding entry had exceeded maximum value <number> for limit, entry has discarded[ on VRF <vrf id>].
1920a007	An entry was discarded because the IPv6 multicast forwarding entry items exceeded the maximum value <number>. <number>: Maximum number of IPv6 multicast forwarding entry items <vrf id> VRF ID [Action] An unauthorized access might have occurred. Check if more than the expected number of additional requests for multicast forwarding entries were generated. The number of multicast forwarding entry items exceeds the maximum value. Check if a negative cache is generated, due to reception of multicast packets that were not forwarded. Check the configuration (ipv6 pim mcache-limit command). Check the network configuration and reconsider the configuration of the Switch.
1920a008	E3	IPv6 multicast forwarding entry has recovered from the state of discard[ on VRF <vrf id>].
1920a008	IPv6 multicast forwarding entries have recovered from the discard state. <vrf id> VRF ID [Action] None.
1e001000	E7	flowd aborted.
	The flow statistics agent program (flowd) was forced to stop. [Action] The flow statistics agent program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	flowd restarted.
	The flow statistics agent program (flowd) has restarted. The switch outputs this message when the flow statistics agent program restarts automatically or a restart is requested by the restart sflow command. [Action] None.
1f00b011	E7	dhcp6_server aborted.
	The IPv6 DHCP server program (dhcp6_server) was forced to stop. The IPv6 DHCP server detected an anomaly such as a lack of memory, aborted the operation, and forced the program to stop. [Action] The IPv6 DHCP server program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	dhcp6_server restarted.
	The IPv6 DHCP server program (dhcp6_server) has restarted. This message is displayed when IPv6 DHCP server program restarts automatically or when a restart is requested by restart ipv6-dhcp server command. [Action] None.
1f01b021	E7	dhcp6_relay aborted.
	The IPv6 DHCP relay program (dhcp6_relay) was forced to stop. The IPv6 DHCP relay detected an anomaly such as a lack of memory, aborted the operation, and forced the program to stop. [Action] The IPv6 DHCP relay program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	dhcp6_relay restarted.
	The IPv6 DHCP relay program (dhcp6_relay) has restarted. The switch outputs this message when the IPv6 DHCP relay program restarts automatically or a restart is requested by the restart ipv6-dhcp relay command. [Action] None.
1f01b024	E3	IPv6 DHCP packet discarded by relay agent, because prefix entry exceeded the maximum.
1f01b024	The relay agent discarded IPv6 DHCP packets because the number of prefix entries exceeded the maximum number. After output of this message, output of the same message is suppressed for the next five minutes. [Action] Use the show ipv6 dhcp relay binding command to check the capacity client count. If the capacity client count for the Switch exceeds the capacity limit, reexamine and then change the capacity client count. If you want to check the number of IPv6 DHCP packets that have actually been discarded, execute the show ipv6 dhcp traffic command to display the IPv6 DHCP relay statistics and check the items in lease prefix over.