3.12.3 Maximum number of configurations that can be set on the Switch
The table below describes the maximum number of route configurations that can be set for each routing protocol.
The numbers shown in this table are the maximum numbers that can be specified by the configuration. Make sure to stay within all capacity limits shown in this chapter during operation.
|
Category |
Configuration commands |
Definition of "maximum number" |
Maximum number of settings |
|---|---|---|---|
|
IPv4 static |
ip route |
Number of lines |
12288 |
|
IPv6 static |
ipv6 route |
Number of lines |
2048 |
|
IPv4 summarized route |
ip summary-address |
Number of lines |
1024 |
|
IPv6 summarized route |
ipv6 summary-address |
Number of lines |
1024 |
|
RIP |
network |
Number of lines |
128 |
|
ip rip authentication key |
Number of lines |
512 |
|
|
address-family ipv4 |
Number of lines |
31 |
|
|
RIPng |
ipv6 rip enable |
Number of lines |
128 |
|
ipv6 router rip |
Number of lines |
32 |
|
|
OSPF |
area range |
Number of lines |
1024 |
|
area virtual-link |
Total number of lines for which parameters authentication-key and message-digest-key have been specified |
512 |
|
|
ip ospf authentication-key ip ospf message-digest-key |
Total number of lines for each command |
512 |
|
|
network |
Number of lines |
256 |
|
|
router ospf |
Number of lines |
256 |
|
|
OSPF commands that you configure for interfaces passive-interface |
Number of configured interfaces (including loopback interfaces) |
288 |
|
|
OSPFv3 |
area range |
Number of lines |
1024 |
|
ipv6 router ospf |
Number of lines |
256 |
|
|
OSPFv3 commands that you configure for interfaces passive-interface |
Number of configured interfaces (including loopback interfaces) |
288 |
|
|
BGP4 |
network |
Number of lines |
1024 |
|
address-family ipv4 |
Number of lines |
31 |
|
|
BGP4+ |
network |
Number of lines |
1024 |
|
address-family ipv6 |
Number of lines |
32 |
|
|
Route filtering |
distribute-list in (RIP) distribute-list out (RIP) redistribute (RIP) |
Total number of lines for each command |
500 |
|
distribute-list in (OSPF) distribute-list out (OSPF) redistribute (OSPF) |
Total number of lines for each command |
500 |
|
|
distribute-list in (BGP4) distribute-list out (BGP4) redistribute (BGP4) |
Total number of lines for each command |
500 |
|
|
distribute-list in (RIPng) distribute-list out (RIPng) redistribute (RIPng) |
Total number of lines for each command |
500 |
|
|
distribute-list in (OSPFv3) distribute-list out (OSPFv3) redistribute (OSPFv3) |
Total number of lines for each command |
500 |
|
|
distribute-list in (BGP4+) distribute-list out (BGP4+) redistribute (BGP4+) |
Total number of lines for each command |
500 |
|
|
ip as-path access-list |
Number of setting <Id> types |
200 |
|
|
Number of lines |
1024 |
||
|
ip community-list |
Number of setting <Id> types |
100 |
|
|
Number of lines with the standard setting |
100 |
||
|
Number of lines with the expanded setting |
100 |
||
|
ip prefix-list |
Number of setting <Id> types |
1024 |
|
|
Number of lines |
4096 |
||
|
ipv6 prefix-list |
Number of setting <Id> types |
1024 |
|
|
Number of lines |
4096 |
||
|
neighbor in (BGP4) neighbor out (BGP4) |
Total number of lines with the <IPv4-Address> setting |
500 |
|
|
Total number of lines with the <Peer-Group> setting |
500 |
||
|
neighbor in (BGP4+) neighbor out (BGP4+) |
Total number of lines with the <IPv6-Address> setting |
500 |
|
|
Total number of lines with the <Peer-Group> setting |
500 |
||
|
route-map |
Number of setting <Id> types |
256 |
|
|
Number of <Id> and <Seq> combinations |
4096 |
||
|
match as-path |
Total number of parameters specified for each line |
2048 |
|
|
match community |
Total number of parameters specified for each line |
2048 |
|
|
match interface |
Total number of parameters specified for each line |
2048 |
|
|
match ip address match ipv6 address |
Total number of parameters specified for each line |
2048 |
|
|
match ip route-source match ipv6 route-source |
Total number of parameters specified for each line |
2048 |
|
|
match origin |
Number of lines |
2048 |
|
|
match protocol |
Total number of parameters specified for each line |
2048 |
|
|
match route-type |
Number of lines |
2048 |
|
|
match tag |
Total number of parameters specified for each line |
2048 |
|
|
match vrf |
Total number of parameters specified for each line |
1024 |
|
|
set as-path prepend count set distance set local-preference set metric set metric-type set origin set tag |
Number of <Id> and <Seq> combinations for route-map in which any one of these parameters is specified |
2048 |
|
|
set community |
Total number of parameters specified for each line |
2048 |
|
|
set community-delete |
Total number of parameters specified for each line |
2048 |