9.1.1 Command list
The following tables list the commands used to configure Web authentication.
Command name |
Description |
---|---|
aaa accounting web-authentication default start-stop group radius |
Enables accounting for Web authentication sessions. |
aaa authentication web-authentication default group radius |
Specifies RADIUS as the default method for Web authentication. |
web-authentication auto-logout |
Configures forced logout based on MAC address aging. |
web-authentication ip address |
Specifies the Web authentication IP address for use in fixed VLAN mode and dynamic VLAN mode. |
web-authentication jump-url |
Specifies the URL to which terminals are directed after successful authentication. |
web-authentication logging enable |
Sends Web authentication operation log messages to syslog servers or email addresses (using E-Mail). |
web-authentication logout ping tos-windows |
Specifies the TOS value of special pings sent by authenticated terminals. |
web-authentication logout ping ttl |
Specifies the TTL value of special pings sent by authenticated terminals. |
web-authentication logout polling count |
Specifies the number of times the switch resends the monitoring packet when there is no response. |
web-authentication logout polling enable |
Enables the connection monitoring functionality that monitors the operation of authenticated terminals. |
web-authentication logout polling interval |
Specifies the interval between transmissions of monitoring (ARP) packets by the connection monitoring functionality. |
web-authentication logout polling retry-interval |
Specifies the interval between retransmissions of monitoring (ARP) packets when there is no response. |
web-authentication max-timer |
Specifies the maximum connection time for Web-authenticated users. |
web-authentication max-user |
Specifies the maximum-number-of-authentications that can be authenticated during dynamic VLAN with Web authentication. |
web-authentication port |
Designates a port as an authenticating port in fixed VLAN mode and dynamic VLAN mode. |
web-authentication radius-server host |
Specify IP of RADIUS servers for Web authentication only. |
web-authentication redirect enable |
Enables URL redirection. |
web-authentication redirect-mode |
Specifies the protocol (HTTP or HTTPS) used to display login pages on a terminal subject to URL redirection. |
web-authentication ssl connection-timeout |
Sets SSL session-establishment timeout. |
web-authentication static-vlan max-user |
Specifies the maximum number of authenticated users permitted in fixed VLAN mode. |
web-authentication system-auth-control |
Enables Web authentication. |
web-authentication web-port |
Adds an access port capable of Web server access. |
The following tables list the operation commands for Web authentication.
Command name |
Description |
---|---|
set web-authentication user |
Adds a user ID for a new Web-authenticated user. |
set web-authentication passwd |
Changes the password of a registered user. |
set web-authentication vlan |
Changes the VLAN ID assigned to a registered user. |
remove web-authentication user |
Deletes a registered user ID. |
commit web-authentication |
Applies any additions or changes you made to the internal Web authentication DB. |
store web-authentication |
Backs up the internal Web authentication DB to a file. |
load web-authentication |
Restores the internal Web authentication DB from a backup file. |
show web-authentication user |
Shows the contents of the internal Web authentication DB and any pending additions or changes. |
clear web-authentication auth-state |
Forcibly logs out an authenticated user. |
show web-authentication login |
Shows accounting log information for authenticated accounts. |
show web-authentication |
Shows the configuration for Web authentication. |
show web-authentication statistics |
Shows statistics for Web authentication. |
clear web-authentication statistics |
Clears the statistics. |
show web-authentication logging |
Shows the operation logs related to Web authentication. |
clear web-authentication logging |
Clears the operation logs related to Web authentication. |
set web-authentication html-files |
Registers the specified Web authentication page files. |
clear web-authentication html-files |
Deletes the Web authentication page files you registered. |
show web-authentication html-files |
Shows the file names and sizes of the Web authentication page files, as well as the date and time of their registration. |
clear web-authentication dead-interval-timer |
Directs the switch to return to accessing the first RADIUS server, having moved on to another RADIUS server as a result of the dead interval functionality. |
set web-authentication ssl-crt |
Register the server certificate and private key for SSL communication. |
clear web-authentication ssl-crt |
Deletes the registered SSL certificate and private key. |
show web-authentication ssl-crt |
Displays the registered SSL certificate and private key. |
restart web-authentication |
Restarts the Web authentication software. |
dump protocols web-authentication |
Creates a dump file of information related to Web authentication. |