2.4.7 20XXXXXX-2aXXXXXX

This section describes operation messages in which the two most significant digits of the message identifier are 2a from 20.

Table 2-10: Operation messages for event location SOFTWARE (20XXXXXX-)
Message ID	Event Level	Message text
Message ID	Content and response
20110001	E7	stpd aborted
	The Spanning Tree program (STPd) was forced to stop. [Action] Collect the error save information (stpd.core file under /usr/var/core), log information, and the configuration of the Spanning Tree program. Refer to the Troubleshooting Guide for information on how to collect. The Spanning Tree program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	stpd restarted
	The Spanning Tree program (stpd) has restarted. This message is displayed when the Spanning Tree program restarts automatically or when a restart is requested by restart spanning-tree and restart uplink-redundant commands. [Action] None.
20120001	E7	LAd aborted
	The link aggregation program (LAd) was forced to stop. [Action] Collect the error save information (LAd.core file under /usr/var/core), log information, and the configuration of the link aggregation program. Refer to the Troubleshooting Guide for information on how to collect. The link aggregation program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	LAd restarted.
	The link aggregation program (LAd) has restarted. The switch outputs this message when the link aggregation program restarts automatically or a restart is requested by the restart link-aggregation command. [Action] None.
20130001	E7	gsrpd aborted.
20130001	The GSRP program (gsrpd) was forced to stop. [Action] Collect the error save information (gsrpd.core file under /usr/var/core), log information, and the configuration of the GSRP program. Refer to the Troubleshooting Guide for information on how to collect. The GSRP program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
20130002	R7	gsrpd restarted.
20130002	The GSRP program (gsrpd) has restarted. The switch outputs this message when the GSRP program restarts automatically or a restart is requested by the restart gsrp command. [Action] None.
20140001	E7	lldpd aborted.
	The LLDP program (lldpd) was forced to stop. [Action] The LLDP program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	lldpd restarted.
	The LLDP program (lldpd) has restarted. The switch outputs this message when the LLDP program restarts automatically or a restart is requested by the restart lldp command. [Action] None.
20160001	E7	L2MacManager aborted.
	L2MAC manager program (L2MacManager) was forced to stop. [Action] The L2MAC manager program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	L2MacManager restarted.
	The L2MAC manager program (L2MacManager) has restarted. The switch outputs this message when the L2MAC manager program restarts automatically or a restart is requested by the restart vlan command. [Action] None.
20160002	E4	The MAC-VLAN MAC Address entry can't be registered at hardware tables.
20160002	The MAC address that was set with the MAC VLAN configuration command could not be set for the hardware. [Action] Review the capacity limit. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
20170001	E7	axrpd aborted.
	The Ring Protocol program (axrpd) was forced to stop. [Action] Collect error save information, logging information, and configuration information for Ring Protocol program. Refer to the Troubleshooting Guide for information on how to collect. Fault recovery information is shown below. Storage directory: /usr/var/core/ File:axrpd.core The Ring Protocol program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	axrpd restarted.
	The Ring Protocol program (axrpd) has restarted. The switch outputs this message when the Ring Protocol program restarts automatically or a restart is requested by the restart axrp command. [Action] None.
20400001	E7	dot1xd aborted
	The IEEE 802.1X program (dot1xd) was forced to stop. [Action] The IEEE 802.1X program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	dot1xd restarted.
	IEEE 802.1X program (dot1xd) has restarted. The switch outputs this message when the IEEE 802.1X program restarts automatically or a restart is requested by the restart dot1x command. [Action] None.
20400003	E4	The 802.1X Supplicant MAC address can't be registered at hardware tables.
20400003	The MAC address of a terminal, which had been successfully authenticated with IEEE 802.1X, could not be set in the hardware table. [Action] Review the capacity limit. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
20400004	E4	The 802.1X Supplicant MAC address of MAC VLAN can't be registered at hardware tables.
20400004	The MAC address of a terminal, which had been successfully authenticated at a MAC VLAN with IEEE 802.1X, could not be set in the hardware table. [Action] Review the capacity limit. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
20420001	E7	wad aborted.
	The Web authentication program (wad) was forced to stop. [Action] The Web authentication program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	wad restarted.
	The Web authentication program (wad) has restarted. The switch outputs this message when the Web authentication program restarts automatically or a restart is requested by the restart web-authentication command. [Action] Perform authentication again on the authentication client side.
20420002	E4	The wad MAC Address entry can't be registered at hardware tables.
20420002	Using the Web authentication function, the MAC address of a terminal could not be set in the hardware table. [Action] Review the capacity limit. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
20420003	E4	The wad MAC Address entry failed in the deletion.
20420003	Using the Web authentication function, the MAC address of a registered terminal could not be deleted from the hardware table. [Action] Restart L2MAC manager program (L2MacManager).
20430001	E7	macauthd aborted.
	The MAC authentication program was forced to stop. [Action] The MAC authentication program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	macauthd restarted.
	The MAC authentication program has restarted. The switch outputs this message when the MAC authentication program restarts automatically or a restart is requested by the restart mac-authentication command. [Action] Perform authentication again on the authentication client side.
20430002	E4	The macauthd MAC address entry can't be registered at hardware tables.
20430002	Using MAC authentication, the MAC address of a terminal could not be set in the hardware table. [Action] Review the capacity limit. However, depending on the hardware specification, the setting to the maximum of the capacity limit might not be available.
20430003	E4	The macauthd MAC address entry failed in the deletion.
20430003	Using MAC authentication, the MAC address of a registered terminal could not be deleted from the hardware table. [Action] Restart L2MacManager.
20700001	E7	efmoamd aborted.
	The IEEE 802.3ah/OAM program (efmoamd) was forced to stop. [Action] The IEEE 802.3ah/OAM program should restart automatically. If it does not restart if restarts occur frequently, restart the switch.
	R7	efmoamd restarted.
	The IEEE 802.3ah/OAM program (efmoamd) has restarted. The switch outputs this message when the IEEE 802.3ah/OAM program restarts automatically or a restart is requested by the restart efmoam command. [Action] None.
20800001	E7	l2ldd aborted.
	The L2 loop detection program (l2ldd) was forced to stop. [Action] The L2 loop detection manager program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	l2ldd restarted.
	The L2 loop detection program (l2ldd) has restarted. The switch outputs this message when the L2 loop detection program restarts automatically or a restart is requested by the restart loop-detection command. [Action] None.
20900001	E7	cfmd aborted.
	The CFM program (cfmd) was forced to stop. [Action] Collect the error save information (cfmd.core file under /usr/var/core), log information, and the configuration of the CFM program. Refer to the Troubleshooting Guide for information on how to collect. The CFM program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	cfmd restarted.
	The CFM program (cfmd) has restarted. The switch outputs this message when the CFM program restarts automatically or a restart is requested by the restart cfm command. [Action] None.
21000001	E7	snoopd aborted.
	The IGMP snooping/MLD snooping program (snoopd) was forced to stop. [Action] The IGMP snooping/MLD snooping program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	snoopd restarted.
	The IGMP snooping/MLD snooping program (snoopd) has restarted. The switch outputs this message when the IGMP snooping/MLD snooping program restarts automatically or a restart is requested by the restart snooping command. [Action] None.
25300000	E7	nimd aborted.
	The network interface manager program (nimd) was forced to stop. [Action] The network interface manager program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	nimd restarted.
	The network interface manager program (nimd) has restarted. The switch outputs this message when the network interface manager program restarts automatically or a restart is requested by the restart vlan command. None.
26100005	E9	System will restart due to software failure occurred during operation.
26100005	The Switch is restarted because a software error occurred during operation. [Action] Use show logging command to check the log. If another error has occurred, take the appropriate action.
27000001	E7	accountingd aborted.
	The accounting program (accountingd) was forced to stop. [Action] Collect the error save information (acctd.core file under /usr/var/core), log information, and the configuration of the accounting program. Refer to the Troubleshooting Guide for information on how to collect. The accounting program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	accountingd restarted.
	The accounting program (accountingd) has restarted. The switch outputs this message when the accounting program restarts automatically or a restart is requested by the restart accounting command. [Action] None.
27000011	E7	System accounting temporary stopped because accounting event congestion detected.
	Accounting event transmission is congested, and accounting of the login and logout commands was stopped temporarily. [Action] Using the show accounting command, make sure that the RADIUS server or TACACS+ server is not issuing errors. Check the configuration settings for the RADIUS server or TACACS+ server that is issuing errors. Additionally, make sure that the configurations on the RADIUS server or TACACS+ server side are correct. The congested state will be resolved when any of the following occur: When the number of transmission queue accounting events decreases to 256, after transmission with the RADIUS server or TACACS+ server has recovered. You can check the number of transmission queue accounting events by checking the item displayed in InQueue of the show accounting command. When the restart accounting command is executed. When the accounting-related configuration is changed as follows: aaa accounting exec, aaa accounting commands, commands related to radius-server, commands related to tacacs-server, IP address of the interface loopback mode
	R7	System accounting recovered from congestion.
	The accounting event transmission has recovered from congestion, and accounting of login and logout commands resumed. [Action] None.
27000013	E4	System accounting failed (<number> times).
27000013	Accounting for the login and logout commands failed. This message appears at intervals when accounting fails. If accounting succeeds even once or no failure occurs for one hour, the failure count is cleared. <number>: Count of consecutive failures [Action] Check if the configurations for RADIUS server or TACACS+ have been set. Check the configurations to make sure that the IP address for RADIUS server or TACACS+ server is correct. Check the configurations to make sure that the port number for RADIUS server or TACACS+ server is correct.
2a001000	E7	httpd aborted.
	The HTTP program (httpd) was forced to stop. [Action] The HTTP program should restart automatically. If it does not restart or if restarts occur frequently, restart the switch.
	R7	httpd restarted.
	The HTTP program (httpd) has restarted. This message is displayed when HTTP programme is automatically restarted. [Action] None.
2a001001	E3	httpd initialization failed(<reason>).
2a001001	Failed to start HTTP programme (httpd). <reason>: Reason for the failure Cannot bind to port <number>(TCP <number> is duplicated with another function. If two or more TCP port numbers are duplicated, the first number detected is displayed.) [Action] Eliminate the duplication of TCP port. Then, use restart web-authentication web-server command. Restart HTTP program.