2.1 BCU
メッセージ種別BCUのシステムメッセージを次の表に示します。
メッセージ 識別子 |
イベント レベル |
メッセージテキスト |
---|---|---|
内容と対応 |
||
00003001 |
S6 |
The BCU restarted because the RESET switch was pressed. |
リセットスイッチが押されたため,BCUを再起動しました。 [対応] なし。 |
||
00003002 |
S6 |
The BCU restarted because of a default restart. |
デフォルトリスタートによってBCUを再起動しました。 [対応] なし。 |
||
00003003 |
S0 |
The BCU restarted because the software detected a fatal error. |
致命的障害をソフトウェアが検出したため,BCUを再起動しました。 [対応] ダンプ情報,ログ情報,およびコンフィグレーションを収集してください。収集方法については,「トラブルシューティングガイド」を参照してください。 |
||
00003004 |
S1 |
The BCU restarted because the software detected a fatal error. |
致命的障害をソフトウェアが検出したため,BCUを再起動しました。 [対応] ダンプ情報,ログ情報,およびコンフィグレーションを収集してください。収集方法については,「トラブルシューティングガイド」を参照してください。 |
||
00003005 |
S6 |
The BCU restarted because of a user operation. |
reloadコマンドによってBCUを再起動しました。 [対応] なし。 |
||
00003006 |
S0 |
The BCU restarted because the kernel detected a fatal software error. |
ソフトウェアの致命的障害をカーネルが検出したため,BCUを再起動しました。 [対応] ダンプ情報,ログ情報,およびコンフィグレーションを収集してください。収集方法については,「トラブルシューティングガイド」を参照してください。 |
||
00003007 |
S1 |
The BCU restarted because the kernel detected a fatal software error. |
ソフトウェアの致命的障害をカーネルが検出したため,BCUを再起動しました。 [対応] ダンプ情報,ログ情報,およびコンフィグレーションを収集してください。収集方法については,「トラブルシューティングガイド」を参照してください。 |
||
00003008 |
S0 |
The BCU restarted because of a WDT timeout. |
WDT(ウォッチドッグタイマ)タイムアウトによってBCUを再起動しました。 [対応] ダンプ情報,ログ情報,およびコンフィグレーションを収集してください。収集方法については,「トラブルシューティングガイド」を参照してください。 |
||
00003009 |
S1 |
The BCU restarted because of a WDT timeout. |
WDT(ウォッチドッグタイマ)タイムアウトによってBCUを再起動しました。 [対応] ダンプ情報,ログ情報,およびコンフィグレーションを収集してください。収集方法については,「トラブルシューティングガイド」を参照してください。 |
||
00003010 |
S0 |
The BCU restarted because the kernel detected a fatal hardware error. |
ハードウェアの致命的障害をカーネルが検出したため,BCUを再起動しました。 [対応] BCUを交換してください。 |
||
00003011 |
S1 |
The BCU restarted because the kernel detected a fatal hardware error. |
ハードウェアの致命的障害をカーネルが検出したため,BCUを再起動しました。 [対応] BCUを交換してください。 |
||
00003012 |
S0 |
The BCU restarted because the hardware detected a fatal hardware error. |
ハードウェアの致命的障害をハードウェアが検出したため,BCUを再起動しました。 [対応] BCUを交換してください。 |
||
00003013 |
S1 |
The BCU restarted because the hardware detected a fatal hardware error. |
ハードウェアの致命的障害をハードウェアが検出したため,BCUを再起動しました。 [対応] BCUを交換してください。 |
||
00003014 |
S6 |
The BCU restarted because of an auto restart by software. |
ソフトウェアによる自動再起動によってBCUを再起動しました。 [対応] なし。 |
||
00003015 |
S6 |
The BCU restarted because the ACH switch was pressed. |
ACHスイッチが押されたため,BCUを再起動しました。 [対応] なし。 |
||
00003016 |
S0 |
The BCU will restart to correct a transient error. When the BCU corrects the error, there is no need to change the BCU. |
一時的な故障を修復するため,BCUを再起動します。 一時的な故障が正常に修復できた場合,BCUの交換は不要です。 [対応] 再起動後に,障害の回復に成功したかどうかをメッセージで確認してください。成功した場合(正常に再起動が完了した場合)は継続して運用できるため,BCUの交換は不要です。失敗した場合(回復中に障害が発生した場合)は,BCUを交換してください。 |
||
00003017 |
S1 |
The BCU will restart to correct a transient error. When the BCU corrects the error, there is no need to change the BCU. |
一時的な故障を修復するため,BCUを再起動します。 一時的な故障が正常に修復できた場合,BCUの交換は不要です。 [対応] 再起動後に,障害の回復に成功したかどうかをメッセージで確認してください。成功した場合(正常に再起動が完了した場合)は継続して運用できるため,BCUの交換は不要です。失敗した場合(回復中に障害が発生した場合)は,BCUを交換してください。 |
||
00200100 |
S3 |
An access error was detected on the internal flash memory. |
内蔵フラッシュメモリへのアクセスエラーを検出しました。 [対応] BCUを交換してください。 |
||
00200201 |
S1 |
The BCU will restart to correct a transient error. When the BCU corrects the error, there is no need to change the BCU. |
一時的な故障を修復するため,BCUを再起動します。 一時的な故障が正常に修復できた場合,BCUの交換は不要です。 [対応] 再起動後に,障害の回復に成功したかどうかをメッセージで確認してください。成功した場合(正常に再起動が完了した場合)は継続して運用できるため,BCUの交換は不要です。失敗した場合(回復中に障害が発生した場合)は,BCUを交換してください。 |
||
01101001 |
S6 |
Initialization is complete. |
初期化が完了しました。 [対応] なし。 |
||
01101002 |
S3 |
Initialization failed because the BCU is unknown. |
不明なBCUのため,初期化できません。 [対応]
|
||
01101003 |
S6 |
The BCU will be restarted because of the user operation. |
ユーザ操作によってBCUを再起動します。 [対応] なし。 |
||
01101004 |
S6 |
The BCU will be restarted because the RESET switch was pressed. |
リセットスイッチによってBCUを再起動します。 [対応] なし。 |
||
01101005 |
S5 |
The BCU redundancy status changed from duplex to simplex. |
BCUの二重化状態が,二重化運用中から一重化運用中に変わりました。 [対応] なし。 |
||
01101006 |
S6 |
The BCU redundancy status changed from simplex to duplex. |
BCUの二重化状態が,一重化運用中から二重化運用中に変わりました。 [対応] なし。 |
||
01101007 |
S6 |
The other BCU went down. |
他系のBCUがダウンしました。 [対応] なし。 |
||
01101008 |
S6 |
The time was synchronized with the time of the active BCU. |
時刻を運用系に合わせました。このメッセージは待機系でだけ表示されます。 [対応] なし。 |
||
01101009 |
S6 |
The standby BCU will be inactivated by a command operation. |
コマンド操作によって待機系BCUを停止します。 [対応] なし。 |
||
0110100a |
S6 |
The standby BCU will be activated by a command operation. |
コマンド操作によって待機系BCUを起動します。 [対応] なし。 |
||
0110100b |
S6 |
The standby BCU will be inactivated by an operation from the system operation panel. |
システム操作パネルからの操作によって,待機系BCUを停止します。 [対応] なし。 |
||
0110100c |
S6 |
The standby BCU will be activated by an operation from the system operation panel. |
システム操作パネルからの操作によって,待機系BCUを起動します。 [対応] なし。 |
||
0110100d |
S5 |
The BCU was switched over from standby to active. |
待機系から運用系に切り替えました。 [対応]
|
||
0110100e |
S5 |
The BCU was switched over from active to standby. |
運用系から待機系に切り替えました。 [対応]
|
||
0110100f |
S6 |
The BCU will be restarted because of a BCU switchover occurred. |
二重化運用中ではない状態で系切替が発生したため,BCUを再起動します。このメッセージは新運用系で表示されます。 [対応] なし。 |
||
01101010 |
S6 |
The BCU will be switched over from active to standby and restart, because the ACH switch was pressed. |
ACHスイッチが押されたため,運用系から待機系に切り替えてBCUを再起動します。 [対応] なし。 |
||
01101011 |
S3 |
A fatal error was detected on the other BCU. |
他系のBCUで致命的な障害が発生しました。 [対応] 他系BCUが再起動したあと,show loggingコマンドまたはshow logging standbyコマンドを実行して障害内容を確認して,そのメッセージに合わせて対応してください。 |
||
01101012 |
S3 |
An error was detected by the health check between the active BCU and the standby BCU. |
BCU間のヘルスチェックで,エラーを検出しました。 [対応]
|
||
01101013 |
S3 |
An error was detected by a health check of the BCU. |
BCU内のヘルスチェックで,エラーを検出しました。 [対応]
|
||
01101014 |
S1 |
The BCU will be restarted because a hardware error was detected. |
ハードウェア障害を検出したため,BCUを再起動します。 [対応] BCUを交換してください。 |
||
01101015 |
S5 |
The BCU has been extracted. |
BCUの抜去を検出しました。 [対応] BCUが抜去された,または正しく挿入されていないおそれがあります。BCUが正しく挿入されているか確認してください。 |
||
01101016 |
S5 |
The BCU has been inserted. |
BCUの挿入を検出しました。 [対応] なし。 |
||
01101017 |
S6 |
The BCU redundancy switchover is available. |
BCUの系切替が可能です。 [対応] なし。 |
||
01101018 |
S3 |
A failure recovery of the BCU has been restrained. |
BCU障害からの復旧は抑止されています。 [対応] show loggingコマンドでログを確認して,障害が発生している場合はそのメッセージに対応した処置をしてください。 障害状態から復旧するには,BCUを交換するか,またはBCUを再起動してください。 |
||
01211001 |
S4 |
The inlet temperature of the device dropped to 2 degrees C or less, and a low temperature warning was detected. |
装置の入気温度が2℃以下になって低温注意を検出しました。 [対応] 装置周辺の環境(室温など)を確認して,改善してください。 |
||
01211002 |
S6 |
The low temperature warning was cleared because the inlet temperature of the device rose to 5 degrees C or more. |
装置の入気温度が5℃以上になったため,低温注意から回復しました。 [対応] なし。 |
||
01211003 |
S4 |
The inlet temperature of the device rose to 43 degrees C or more, and a high temperature warning was detected. |
装置の入気温度が43℃以上になって高温注意を検出しました。 [対応]
|
||
01211004 |
S6 |
The high temperature warning was cleared because the inlet temperature of the device dropped to 40 degrees C or less. |
装置の入気温度が40℃以下になったため,高温注意から回復しました。 [対応] なし。 |
||
01211005 |
S4 |
The inlet temperature of the device rose to 53 degrees C or more, and is approaching a high temperature that might affect device operation. |
装置の入気温度が53℃以上になって,装置の運用に支障を来す温度に近づいています。 [対応]
|
||
01211006 |
S6 |
The inlet temperature of the device has been restored to 50 degrees C or less from a temperature that could have affected device operation. Care must still be taken because the temperature is still over the recommended maximum. |
装置の入気温度が,装置の運用に支障を来す温度から50℃以下に回復しました。しかし,まだ許容範囲を上回る温度なため注意が必要です。 [対応]
|
||
01211007 |
S3 |
The inlet temperature of the device rose to 65 degrees C or more, and has reached a temperature that might severely damage the device. |
装置の入気温度が65℃以上になって,装置の運用に致命的な障害を与える温度に達しました。 [対応]
|
||
01211008 |
S1 |
The BCU will stop because of a hardware failure. |
ハードウェア障害を検出したため,BCUを停止します。 [対応] BCUを交換してください。 |
||
01211009 |
S6 |
The inlet temperature of the device rose to greater than or equal to the temperature set by the 'system temperature-warning-level' configuration command.(temperature = <temperature> degrees C) |
装置の入気温度がコンフィグレーションコマンドsystem temperature-warning-levelで設定した温度以上になりました。
[対応] 装置の温度が指定した温度に達しているため,装置周辺の環境(ファンの状態,通風,熱源の有無など)を確認してください。 |
||
0121100a |
S6 |
The inlet temperature of the device dropped 3 degrees C or more from the temperature set by the 'system temperature-warning-level' configuration command. |
装置の入気温度がコンフィグレーションコマンドsystem temperature-warning-levelで設定した温度より3℃以上下がりました。 [対応] なし。 |
||
0121100b |
S6 |
The mean inlet temperature of the device rose to greater than or equal to temperature set by the 'system temperature-warning-level average' configuration command.(temperature = <average temperature> degrees C) |
装置の平均入気温度がコンフィグレーションコマンドsystem temperature-warning-level averageで設定した温度以上になりました。
[対応] 装置の平均入気温度が指定した温度に達しているため,装置周辺の環境(ファンの状態,通風,熱源の有無など)を確認してください。 |
||
0122100c |
S3 |
Access to the BCU statistics failed. |
BCUの通算稼働時間へのアクセスに失敗しました。 [対応] 通信および通常運用に影響はありません。ただし,通算稼働時間の管理機能が使用できないため,使用する場合はBCUを交換してください。 |
||
0122100d |
S6 |
Access to the BCU statistics finished successfully. |
BCUの通算稼働時間へのアクセスが正常に完了しました。 [対応] なし。 |
||
0122100e |
S4 |
The BCU-CPU memory usage exceeded 98%. |
BCU-CPUのメモリ使用率が98%を超えました。 [対応]
|
||
0122100f |
S6 |
The BCU-CPU memory usage fell below 95%. |
BCU-CPUのメモリ使用率が95%を下回りました。 [対応] なし。 |
||
01221010 |
S3〜S7 |
The internal flash memory has too short free space. |
内蔵フラッシュメモリの未使用容量がコンフィグレーションコマンドsystem flash-monitorで設定した閾値未満になりました。 [対応] ユーザ領域の不要ファイルを削除して,未使用容量を閾値以上にしてください。ユーザ領域の未使用容量および閾値の設定はshow flashコマンドで確認できます。 |
||
01221011 |
S3〜S7 |
The internal flash memory has enough free space. |
内蔵フラッシュメモリの未使用容量がコンフィグレーションコマンドsystem flash-monitorで設定した閾値以上になりました。 [対応] なし。 |
||
09200001 |
S1 |
The BCU will restart because a configuration software error occurred. |
コンフィグレーションソフトウェアに障害が発生したため,BCUを再起動します。 [対応] show loggingコマンドでログを確認して,ほかの障害が発生している場合はそのメッセージに合わせて対応してください。 |
||
09300001 |
S1 |
The BCU will restart because a configuration software error occurred. |
コンフィグレーションソフトウェアに障害が発生したため,BCUを再起動します。 [対応] show loggingコマンドでログを確認して,ほかの障害が発生している場合はそのメッセージに合わせて対応してください。 |
||
09400001 |
S1 |
The BCU will restart because a configuration software error occurred. |
コンフィグレーションソフトウェアに障害が発生したため,BCUを再起動します。 [対応] show loggingコマンドでログを確認して,ほかの障害が発生している場合はそのメッセージに合わせて対応してください。 |
||
09500001 |
S1 |
The BCU will restart because a configuration software error occurred. |
コンフィグレーションソフトウェアに障害が発生したため,BCUを再起動します。 [対応] show loggingコマンドでログを確認して,ほかの障害が発生している場合はそのメッセージに合わせて対応してください。 |
||
09600001 |
S1 |
The BCU will restart because a configuration software error occurred. |
コンフィグレーションソフトウェアに障害が発生したため,BCUを再起動します。 [対応] show loggingコマンドでログを確認して,ほかの障害が発生している場合はそのメッセージに合わせて対応してください。 |
||
25011001 |
S6 |
The port status is Up. |
ポートがUPしました。 [対応] なし。 |
||
25011002 |
S6 |
The port was inactivated by configuration. |
コンフィグレーションコマンドshutdownによってポートを停止しました。 [対応] なし。 |
||
25011003 |
S6 |
The port was activated by configuration. |
コンフィグレーションコマンドno shutdownによってポートを起動しました。 [対応] なし。 |
||
25011004 |
S6 |
The port was inactivated by an operation command. |
inactivateコマンドによってポートを停止しました。 [対応] なし。 |
||
25011005 |
S6 |
The port was activated by an operation command. |
activateコマンドによってポートを起動しました。 [対応] なし。 |
||
25011201 |
S5 |
An error was detected on the port. |
ポートで障害を検出しました。 [対応]
|
||
35000101 |
S6 |
Past event information was initialized because the BCU was switched over from active to standby. |
本装置は運用系BCUから待機系BCUに系切替したため,過去のイベント情報を初期化しました。このメッセージは待機系BCUでだけ表示されます。 [対応] なし。 |
||
35010001 |
S1 |
The BCU will restart because a hardware error was detected. |
ハードウェア障害を検出したため,BCUを再起動します。 [対応] BCUを交換してください。 |
||
35010011 |
S1 |
The BCU will restart to correct a transient error. When the BCU corrects the error, there is no need to change the BCU. |
一時的な故障を修復するため,BCUを再起動します。 一時的な故障が正常に修復できた場合,BCUの交換は不要です。 [対応] 再起動後に,障害の回復に成功したかどうかをメッセージで確認してください。成功した場合(正常に再起動が完了した場合)は継続して運用できるため,BCUの交換は不要です。失敗した場合(回復中に障害が発生した場合)は,BCUを交換してください。 |
||
35020401 |
S4 |
The PA memory usage exceeded 98%. |
PAのメモリ使用率が98%を超えました。 [対応] 長時間PAのメモリ使用率が下がらない場合は,BCUを再起動してください。 |
||
35020402 |
S6 |
The PA memory usage fell below 95%. |
PAのメモリ使用率が95%を下回りました。 [対応] なし。 |
||
350d0101 |
S6 |
The HDC on the BCU will be updated. Do not remove the BCU. |
HDCを更新します。 [対応] BCUを抜去しないでください。 |
||
350d0102 |
S6 |
The BCU will restart because its HDC was updated. |
HDCを更新したため,BCUを再起動します。 [対応] なし。 |
||
350d0103 |
S3 |
The HDC update was unsuccessful on the BCU. |
HDCの更新に失敗しました。 [対応]
|
||
350e0201 |
S6 |
The PA online dump command was executed. |
PAダンプ(BCU再起動なし)コマンドの実行によって,メモリダンプの収集が完了しました。 [対応] なし。 |
||
350e0203 |
S6 |
Collection of the PA dump was canceled. |
ダンプ採取が中断されました。 [対応] なし。 |